Loading...
WA9601-SP 990208S ]MEK, JACOBS & FINKLEA, L.L.P. CONSULTING ENGINEERS DALLAS, TEXAS Date: February 11, 1999 Landmark Structur nc. 1665 Harmon ad Ft. Worth exas 76177 · .nea' · ' Re: City of Coppell Wagon Wheel Ranch Elevated Storage Tank We are transmitting herewith three copies of the submittal data furnished by Landmark Structures, Inc. These copies have been reviewed and marked as follows: Explanation No Make Revise Submit No. Exceptions Corrections and Specified Dwg. No. Sheets Dwg. Description Taken Rejected Noted Resubmit Items 19 Paint Material Data XX Remarks: By copy of this letter we are returning twocopies of the submittal to Mr. Larry Davis, CityCli._,,_.... By: Paul A. Carline, E.I.T. Checking of shop drawings by Shimek, Jacobs & Finklea, L.L.P. is only for general conformance with the design concept of the project and general compliance with the information given in the contract documents. Any action shown is subject to the requirements of the plans and specifications. Contractor is responsible for: dimensions which shall be confirmed and correlated at the job site; fabrication processes and techniques of construction; coordination of his work with that of all other trades; and performing his work in a safe and satisfactory manner. · f LANDMARK STRUCTURES, INC. 1665 Harmon Road Fort Worth, Texas 76177 (817) 439-8888 Fax (817) 439-9001 TO: Shimek, Jacobs & Finklea 8333 Douglas Avenue, Suite 820 Dallas, Texas 75225 LETTER OF TRANSMITTAL Date Job. No. 2/8/99 9802 Att n: Mr. Gary C. Hendricks, P.E. Re: Wagon Wheel Ranch 2.0 MG Elevated Storage Tank Bid No. Q 0198-03 City of Coppell, Texas WE ARE SENDING YOU THE ATTACHED ITEMS: Copies Spec Section Submittal No. 6 S.C. 10 19 Paint Material Data THESE ARE BEING TRANSMITTED: [] NO EXCEPTION TAKEN ~VIAKE CORRECTIONS NOTED [] REJa~f,~tion L.J REVISE AND RESUBMI'~ [] SUBMIT SPECIFIED ITEM Checking is only for general conformance with the desert concept of the project and general compliance with he information given in lhe contract documents. Any action shc, wn is subject to the requirements of the plans ~d specifications. Contractor is responsible for: dimenslcns wh~.h shah be confirn3ed and correlated at the job si:e; fabrication processes and techniques of construction, or~;r,a~on of his work with that of all other trades ~d performing h~s work in a safe and satisfacto~ manner, SHIMEK, JACOBS & FINKLEA CONSULTING ENGINEERS DALES, TE~S Information for Record O&M Data X Information for Engineer's Approval X Return 2 Copies CERTIFICATION: This information has been reviewed and determined to be in compliance with the contract documents including plans and specifications as modified by addenda, change orders and field orders. Any exceptions to the contract documents are noted below. EXCEPTIONS I REMARKS: 1. We are submitting Tnemec as an equal to Valspar as the paint manufacturer. Signed Joe Swinnea f~ Wagon Wheel Ranch 2.0 MG Elevated Storage Tank Project No. WA-96-01 City of Coppell, Texas SUBMITTAL NO. 19 SPEC SECTION S.C. PAINT MATERIAL DATA Interior Surface Preparation: SSPC-SP10 Coatings Tnemec Series Prime FC20-1255 (Beige) Finish FC20-WH02 (Tank White) Minimum D.F.T. 5.0 mils 5.0 mils 10.0 mils Exterior Surface Preparation: SSPC-SP6 Coatings Tnemec Series Prime FC20-1255 (Beige) Intermediate 74-Contrast Finish 74-WH02 (Tank White) Minimum D.F.T. 5.0 mils 2.5 mils 2.5 mils 10.0 mils Logo Lettering Clear Coat Tnemec Series .~. ~ 74 lack Outhn -B ( 'e) 74-Safety Red (llli Lines) 74-Indigo C'" .~ Lines) Minimum D.F.T. 2.5 mils 2 Coats @ 1.5 mils Note: (1) Series FC20 is submitted as an equal to the Series 66 on the exterior and as an equal to the Series 140 on the interior. Our coatings applicator has 100% success rate with the Series FC20 and we prefer to stay with the Series FC20, which will perform as well as, or better than, Series 140. (2) All coatings are to be field applied. Pota-Pox l, Cure) SERIES FC20 T N E M E C PRODUCT PROFILE GENERIC DESCRIPTION Polyamide Epoxy COMMON USAGE Fast-curing protective coating for use in steel and concrete potable water storage facilities. Contact your Tnemec representative for other systems and additional information on potential uses. COLORS Primer: 1211 Red, 1255 Beige. Topcoat: AA90 White, WH02 Tank White, GB03 Delft Blue. Note: Epoxies chalk with extended exposure to sunlight. Lack of ventilation, incomplete mixing, miscatalyzation or the use of heaters that emit carbon dioxide and carbon monoxide during application and initial stages of curing may cause yellowing to occur. SPECIAL QUALIFICATIONS Certified by NSF International in accordance with ANSI/NSF Std. 6!. for use on the interior of potable water storage tanks and reservoirs of 1,000 gallons (3785 L) capacity or greater. Conforms to AWWA D 102 Inside Systenas No. 1 and No. 2. Contact your Tnemec representative for approved systems and additional information on potential uses. PERFORMANCE CRITERIA Extensive test data available. Contact your Tnemec representative for specific test results. COATING SYSTEM PRIMERS TOPCOATS Self-priming, 91-Ha0. Note: 91-H20 is ANSI/NSF Std. 61 certified by ~ as a primer for Series FC20. Refer to the 91-H20 product data sheet for additional information. Interior: Series 20, FC20, 140, 264, 265 Exterior: Series 20, FC20, 27, 66, 69, 71, 73, 74, 75, 104, 140, 161 Refer to COLORS on applicable topcoat data sheets for additional information. Note: Series FC20 exterior exposed for 3 weeks or longer requires an epoxy intermediate coat or scarification prior to topcoating with Series 71. Refer to Series 71 product data sheet for additional information. SURFACE PREPARATION STEEL Immersion Service: SSPC-SP10 Near-White Blast Cleaning Non-Immersion Service: SSPC-SP6 Commercial Blast Cleaning PRIMED SURFACES Immersion Service: Scarify the Series FC20 prime coat surface by brush-blasting with fine abrasive before topcoating if it has been exposed to sunlight for 60 days or longer. CAST/DUCTILE JRON Contact your Tnemec representative or Tnemec Technical Services. CONCRETE Allow new concrete to cure for 28 days. Brush-off blast. Holes, pits, voids and cracks should be filled with 63-1500 Filler and Surfacer (ANSI/NSF Std. 61 certified). ALL SURFACES Must be clean, dry. and free of oil, grease and other contaminants. TECHNICAL DATA VOLUME SOLIDS* RECOMMENDED DFT CURING TIME VOLATILE ORGANIC COMPOUNDS THEORETICAL COVERAGE* NUMBER OF COMPONENTS PACKAGING NET WEIGHT PER GALLON* 58.0 -+ 2.0% (mixed) Primer: 3.0 to 5.0 mils (75 to 125 microns) per coat. Intermediate, Topcoat: 4.0 to 6.0 mils (100 to 150 microns) per coat. Note: Number of coats and thickness requirements will vary with subsirate, application method and exposure. Contact your Tnen~ec representative. Temperature To Touch To Handle To Recoat Immersion 75°F (24°C) 1 hour 2 hours 3 hours 6 days 65°F (18°C) 2 hours 4 hours 5-6 hours 8 days 55°F (13°C) 3-4 hours 6-8 hours 10-12 hours 12 days 45°F (7°C) 6-7 hours 12-14 hours 16-18 hours 20 days 35°F (2°C) 8-10 hours 16-18 hours 20-22 hours 25 days Curing time varies with surface temperature, air movement, humidity and film thickness. Unthinned Thinned 10% 2.90-2.97 Ibs/gallon 3.26-3.32 lbs/gallon (347-356 grams/litre) (391-398 grams/litre) 930 rail sq ft/gal (22.8 m2/L at 25 microns). See APPLICATION for coverage rates. Two: Part A and Part B 5 gallon (18.9L) pails and 1 gallon (3.79L) cans -- Order in multiples of 2. 12.50 _+ 0.25 lbs (5.7 _+ .11 kg) (mixed) © September J-997, by Tnemec Company, Inc. FC20 TECHNICAL DATA STORAGE TEMPERATURE TEMPERATURE RESISTANCE SHELF LIFE FLASN POINT- SETA HEALTH & SAFETY continued Minimum 20°F (-7eC) Maximum ll0eF (43°C) (Dry) Continuous 250°F (121°C) Intermittent 275°F (135eC) 12 months at recommended storage temperature. Part A: 82°F (28°C) Part B: 64°F (18°C) Paint products contain chemical ingredients which are considered hazardous. Read container label warning and Material Safety Data Sheet for important health and safety information prior to the use of this product. Keep out of the reach of children. APPLICATION COVERAGE RATES' MIXING POT LIFE THINNING SURFACE TEMPERATURE APPLICATION EQUIPMENT CLEANUP Pritner Internxediate / Topcoat Dry Mils Wet Mils Sq Ft/Gal Dry Mils Wet Mils Sq Ft/Gal (Microns) (Microns) (m.z/Gal) (Microns) (Microns) (rnz/Gal) Suggested (1) 4.0 (100) 7.0 (180) 232 (21.6) 5.0 (].25) 8.5 (215) 186 (17.3) Minimum 3.0 (75) 5.0 (125) 3].0 (28.8) 4.0 (].00) 7.0 (].80) 232 (2]..6) Maximum 5.0 (].25) 8.5 (2].5) 186 (17.3) 6.0 (150) ].0.5 (265) 155 (14.4) (1) Note: Roller or brush application requires two or more coats to obtain recommended film thickness. Allow for overspray and surface irregularities. Film thickness is rounded to the nearest 0.5 mil or 5 microns. Application of coating below minimum or above maximum recommended dry film thicknesses may adversely affect coating performance. Power mix contents of each container, making sure no pigment remains on the bottom. Pour a measured amount of Part B into a clean container large enough to hold both components. Add an equal volume of Part A to Part B while under agitation. Continue agitation until the two components are thoroughly mixed. Do not use mixed material beyond pot life limits. Note: Both components should be above 50°F (].0°C) prior to mixing. For application to surfaces between 35°F to 50°F (2°C to 10°C), allow mixed material to stand thirty (30) minutes and restLr before using. For optimum application properties, blended components should be above 60°F (16°C). 16 hours at 35°F (2°C) 2 hours at 77°F (25°C) 1/2 hour at 100oF (38°C) Use No. 4 Thinnet. For air spray, thin up to 10% or 3/~ pint (380 mL) per gallon. For airless spray, roller or brush, thin up to 5% or ~/~ pint (190 mL) per gallon. Caution: Series FC20 NSF certifica- tion is based on thinning with No. 4 Thinner. Use of any other thinner voids ANSI/NSF Std. 61 certification. Minimum 35oF (2~C) Maximum 135°F (57°C) The surface should be dry and at least 5°F (3°C) above the dew point. Coating won't cure below minimum surface temperature. Air Spray Gun Fluid Air Cap Air Hose Mat'l Hose Atotnlzlng Pot Tip ID ID Pressure Pressure DeVilbiss E 765 5/16" or 3/8" 3/8" or 1/2" 75-100 psi 10-20 psi MBC orJGA or 78 (7.9 or 9.5 ram) (9-5 or 12.7 ram) (5.2-6.9 bar) (0.7-1.4 bar) Low temperatures or longer hoses require higher pot pressure. Airless Spray Tip Orifice Atomi~ing Pressure Mat'l Hose ID Manifold Filter 0.015"-0.019" 1800-3000 psi 1/4" or 3/8' 60 mesh (380-485 microns) (124-207 bar) (6.4 or 9.5 ram) (250 microns) Use appropriate tip/atomizing pressure for equipment, applicator technique and weather conditions. Plural Component Spray: Contact your Tnemec representative or Tnemec Technical Services. Roller: Roller application optional when environmental restrictions do not allow spraying. Use 3/8' or 1/2' (9.5 mm or 12.7 ram) synthetic nap covers. Brush: Recommended for small areas only. Use high quality natural or synthetic bristle brushes. Flush and clean all equipment immediately after use with the recommended thinner or MEK. *Values may vary with color. WARRANTY & LIMffATION OF SELLER'S UA81LITY: Themac Company, Inc. warrants only thai its coatings represented heroin meet the formulation standards of Themac Company, THE WARRANTY DESCRIBED IN THE ABOVE PARAGRAPH SHALL BE IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUOING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR EftHESS FOR A PARTICULAR PURPOSE. THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOE The buyef's sole and exclusive remedy agoinsl Themac Company, Inc. shaft be for repiacomont of the product in the event a defective condition of the product should be Found ro exist and the exclusive remedy shall not have ~led ils essential purpose as long as Themac is willing to provide comparable rep~emenl product In Ihe buyer. NO OTHER REMEDY (iNCLUDING, BUT NOT LIMITEO TO, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR LOST PROFETS, LOST SALES, INJURY TO PERSON OR PROPERTY, ENVIRONMENTAL INJURIES OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS) SHALL BE AVAILABLE TO THE BUYER. Technical and application ioformation heroin is provided far the purpose of establishing a general profile of the conling and prepor cooling appiicalion procedures. Test performance resulls were abletried in a controlled environmenl and Themac Company makes no claim thai these tesls or any other tesls, accurately represent ull envilonmenls. As application, enviranmentai and design fadors can vary signdiconlly, due care should be exercised in Ihe selection and use of the conling. PUBLJSHED TECHNICAL DATA AND/NSTRUCTIONS ARE SBBJECT TO CHANGE WITHOUT NOTICE. CONTACT YOUR TNEMEC REPRESENTATIVE FOR CURRENT TECHNICAL DATA AND INSTRUCTIONS. FOR INDUSTRIAL USE ONLY. TNEMEC COMPANY ~NCORPORATED PRINTED IN USA 6800 CORPORATE DRIVE, KANSAS CITY, MISSOURI 64120-1372 TEL: 816 483-3400 ~0 Endura l tield .SERIES74 T N E M E C PRODUCT PROFILE GENERIC DESCRIPTION COMMON USAGE COLORS FINISH PERFORMANCE CRITERIA Aliphatic Acrylic Polyurethane A coating highly resistant to abrasion, wet conditions, corrosive fumes, chemical contact and exterior weathering. High build quality combines with project specific primers for two-coat, labor saving systems. NOT FOR IMMERSION SERVICE. Refer to Tnemec ColorBook. Note: Certain colors may require multiple coats depending on method of application and finish coat color. When feasible, the preceding coat should be in the same color family (blue, gray, etc.), but noticeably different. Gloss Extensive test data available. Contact your Tnemec representative for specific test results. COATING SYSTEM PRIMERS Steel: Series 20, 27, 37H, 40, 50-330, 65, 66, 69, 83, 90-97, 104, 135, 140, 160, 161, 163 Galvanized Steel and Non-Ferrous Metal: Series 66, 69, 135, 161, 163 Concrete: Series 66, 69, 104, 161, 163 CMI_I: 54-660 Note: Before topcoating with Series 74, 50-330 exterior exposed more than 24 hours must first be scarified or receive an intermediate coat of Tnemec polyamide epoxy. Also, Series 69, 83, 104, 135 or 140 exterior exposed more than two months must first be scarified or reprimed with themselves. Brush blasting with fine abrasive is the preferred method of scarification. SURFACE PREPAItATION ALL SURFACES Must be clean, dry and free of oil, grease and other contaminants. TECHNICAL DATA VOLUME SOLIDS* RECOMMENDED DFT CURING TIME VOLATILE ORGANIC COMPOUNDS Series 74 THEORETICAL COVERAGE* NUMBER OF COMPONENTS PACKAGING NET WEIGHT PER GALLON* STORAGE TEMPERATURE TEMPERATURE RESISTANCE SHELF LIFE FLASH POINT- SETA HEALTH & SAFETY 70.0 + 2.0% (mixed) 2.0 to 5.0 mils (50 to 125 microns) per coat. Note: Number of coats and thickness require- ments will vary with substrate, application method and exposure. Contact your Tnemec representative. Temperature To Touch To Handle To Recoat [ 75°F (24°C) I hour J 6 hours I 8 hours I To resist moisture condensation: 6 hours. Curing time varies with surface temperature, air movement, humidity and film thickness. Note: For faster curing and low-temperature applications, add No. 44-710 Urethane Accelerator; see separate product data sheet. Unthinned Thinned 10% 2.15-2.48 lbs/gallon (257-297 grams/litre) 1,125 mil sq ft/gal (27.6 mz/L at 25 microns). Two: Part A and Part B (No. 42 Thinner) 2.56-2.86 lbs/gallon (306-342 grams/litre) Five-Gallon Kit: consists of four gallons of Part A in a five gallon pail and a one gallon can of Part B. When mixed, yields five gallons (18.9L). One-Gallon Kit: Consists of a partially-filled one gallon can labeled Part A and a partially filled quart can labeled Part B. When mixed, yields one gallon (3.79L). 11.16 + 0.25 lbs (5.06 _+ .11 kg) Minimum 20~F (-7°C) Maximum ll0°F (43°C) (Dry) Continuous 250°F (121~C) Intermittent 275°F (135°C) 12 months at recommended storage temperature. Part A: 98~F (37°C) Part B: 135°F (57~C) Paint products contain chemical ingredients which are considered hazardous. Read container label warning and Material Safety Data Sheet for important health and safety information prior to the use of this product. Keep out of the reach of children. September 1997, by Tnemec Company, Inc. 74 APPLICATION COVERAGE RATES* MIXING POT LIFE THINNING SURFACE TEMPERATURE APPLICATION EQUIPMENT CLEANUP Conventional Build High-Build (Spray, Brush or Roller) (Spray Only) Dry Mils Wet Mils Sq Ft/Gal Dry Mils Wet Mils Sq Ft/Gal (Microns) (Microns) (rn2/Gal) (Microns) (Microns) (mz/Gal) Suggested 2-5 (65) 3.5 (90) 449 (41.7) 4.0 (100) 5-5 (140) 281 (26.1) Minimum 2.0 (50) 3.0 (75) 561 (52.1) 3.0 (75) 4.5 (115) 374 (34.7) Maximum 3.0 (75) 4.5 (115) 374 (34.7) 5.0 (125) 7.0 (180) 225 (20.9) Note: Can be spray applied at 3.0 to 5.0 mils (75 to 125 microns) DFT per coat when extra protection or the elimination of a coat is desired. Allow for overspray and surface irregularities. Film thickness is rounded to the nearest 0.5 mil or 5 microns. Application of coating below minimum or above maximum recommended dry film thicknesses may adversely affect coating performance. Stir contents of the container marked Part A, making sure no pigment remains on the bottom. Add the contents of the can marked Part B to Part A while under agitation. Continue agitation until the two components are thoroughly mixed. When used with 44-710 Urethane Accelerator, fizst blend 44-710 into Part A under agitation; continue as above. Do not use mixed material beyond pot life limits. Caution: Part B is moisture-sensitive and will react with atmospheric moisture. Keep unused material tightly closed at all times. 2 hours at 77°F (25°C) unthinned 3 hours at 77°F (25°C) thinned 1 hour at 100°F (38°C) unthinned 2 hours at 100°F (38°C) thinned For air or airless spray, thin up to 10% or 3A pint (380 mL) per gallon with No. 42 ThinneE For brush or roller, thin 3% to 5% or ~A pint (190 mL) per gallon with No. 39 ThinneE Thinning is required for proper application. Caution: Do not add thinher if more than thirty (30) minutes have elapsed after mixing. Minimum 40°F (4°C) Maximum 120°F (49°C) The surface should be dry and at least 5°F (3°C) above the dew point. Cure time necessary to resist direct contact with moisture at surface temperature: 40°F (4°C): 24 to 32 hours 50°F (10°C): 18 to 24 hours 60°F (16°C): 7 to 10 hours 70°F (21°C): 4 to 8 hours 90°F (32°C): 2 to 4 hours 100°F (38°C): 1 to 2 hours If the coating is exposed to moisture before the preceding cure parameters are met, dull, fiat or spotty-appearing areas may develop. Actual times will vary with air movement, film thickness and humidity. Air Spray Gun Fluid Air Cap Air Hose Mat'l Hose Atomizing Pot Tip ID ID Pressure Pressure DeVilbiss E 78 5/16" or 3/8" 3/8" or 1/2" 75-90 psi 10-20 psi MBC (7.9 or 9.5 ram) (9.5 or 12.7 ram) (5.2-6.2 bar) (0.7-1.4 bar) Low temperatures or longer hoses require higher pot pressure. Airless Spray Tip Orifice Atomizing Pressure Mat'l Hose ID Manifold Filter 0,009"-0.01Y' 3000-3500 psi 1/4" or 3/8" 100 mesh (230-330 microns) (207-241 bar) (6.4 or 9.5 ram) (150 microns) Use appropriate tip/atomizing pressure for equipment, applicator technique and weather conditions. Roller: Use 1/4" (6.4 ram) synthetic nap cover. Do not use medium or long nap roller covers. Two coats are required to obtain dry film thickness above 3.0 mils (75 microns). Brush: Recommended for small areas only. Use high quality natural or synthetic bristle brushes. Note: Two coats are required to obtain recommended film thickness. Flush and clean all equipment immediately after use with the recommended thinner or MEK. *Values may vary with color. WARRANTY & LIMITATION OF SELLER'S LIABILITY: Toemac Company, Inc. warrants only Ihat its coollogs represenled heroin meet the JotmuMlioo slandards of Themes Company, Inc. /HE WARRANTY DESCRIBED IN THE ABOVE PARAGRAPH SHALL BE IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIEO, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARtiCULAR PURPOSE. THERE ARE NO WARRANTIES THAT EXTEND 8EYONO THE DESCRIPTION ON THE FACE HEREOR The buyot's sole end exclusive Iomedy ogoinsl Tnemes Company, Inc. shall be for reptacemenl DE the product in the eveet o defeulive canaltitan of lhe product should be tound to axial and Ihe exclusive remedy shaU hal have foiled its essential purpose as long os Toemac is willing Io p~avide campotoble replacemenl produd re Ihe buyer. NO OTHER REMEDY (INCLUDING, BUT NOT LIMITEO TO, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR LOST PROFITS. LOST SALES, INJURY [0 PERSON OR PROPERTY, ENVIRONMENTAL INJURIES OR ANY OTHER iNCIDENTAL OR CONSEQUENTIAL LOSS) SHALL BE AVAILABLE TO THE BUYER. Technical Dad application informalion heroin is provided for the potpaso of establishing a general plofile of Ihe cooling and proper coating oppticalion proceclules. Tesl pedotmance results were obteinod in a coalrolled environmenl and Toemac Company makes no claim thai these lenin or Day olhef tesls, accurately represenl nil environments. As opplkalion, environmental and design fadors can vary significanUy, dt~ cote should be exercised in Ihe setsellen ~nd usa at the cooling. PUBLISHED TECHNICAL DATA AND INSTRUCTIONS ARE SUBJECT TO CHANGE 'NITHOUT NOTICE. CONTACT YOUR TNEMEC REPRESENTAtiVE FOR CURRENT TECHNICAL DATA AND INSTRUCTIONS. FOR INDUSTRIAL USE ONLY. /NEMEC COMPANY INCORPORATED PRINIED IN USA 6800 CORPORAtE DRIVE, KANSAS CITY, MISSOURI 64120-1372 TEL: 816 483-3400 74 TNE.~IEC :PRODUCT PROFILE GENERIC DESCRIPTION COMMON USAGE COLOR FINISH PERFORMANCE CRITERIA COATING SYSTEM BASE COATS Aliphatic Acrylic Polyurethane A unique clear coat used to both en ' finish and extend the long-term weathering qualities of pigmented Endura- ost graffiti markings. H~gh gloss E~tensive test d . ec representative for specific test results. Series 71, 73,~5, 175. Note: Series 76 Endura-Clear should be applied within 7 days of a Series 71 or 175 application; within 14 days of a Series 75 application; and within 21 days of a Series 73 application. SURFACE PREPARATION Prepare surfaces by method suitable for exposure and sereice. (See Primer Product Data Sheet for surface preparation recommendations.) ALL SURFACES Must be clean, dry. and free of oil, grease and other contaminants. TECHNICA.L DATA VOLUME SOLIDS RECOMMENDED DFT CURING TIME VOLATILE ORGANIC COMPOUNDS THEORETICAL COVERAGE NUMBER OF COMPONENTS P,~CKAGING NET WEIGHT PER GALLON STORAGE TEMPERATURE TEMPERATURE RESISTANCE SHELF LIFE FLASH POINT- SETA HEALTH & SAFETY 66.0 _. 2.0% (mixed) 1.0 to 2.0 mils (25 to 50 microns) per coat. To Re(oat * J 72 hours Temperature To Touch To Handle To Recoat I 75o (24o0 I ,,2-1 hour I 2-3 hours I 3 hours I To resist moisture condensation: 3 hours Curing time varies with surface temperature, air movement, humidity and film thickness. * If exceeded, scarify before applying an additional coat. Unthinned Thinned 10% Thinned 20% 2.40-2.67 lbs/gallon 2.84-3.09 lbs/gallon 3.21-3.43 lbs/gallon (288-320 grams/litre) (340-370 grams/litre) (384-411 grams/litre) 1,059 rail sq ft/gal (26.0 m2/L at 25 microns). See APPLICATION for coverage rates. Three: Part A, Part B and Part C Large Kit: Consists of two one-gallon cans of Part A, one one-gallon can of Part B and a one- quart plastic bottle of Part C. When mixed yields 3.25 gallons. Small Kit: Consists of a partially filled one-gallon can of Part A, a quart can of Part B and an eight-ounce plastic bottle of Part C. When mixed yields .81 gallon. 8.71 _+ 0.20 lbs (3.95 + .09 kg) (mixed) Minimum 20°F (-7°C) Maximum 110°F (43°C) (Dry) Continuous 250°F (121°C) Intermittent 275°F (135~C) Parts A and B: 12 months at recommended storage temperature. Part C: 6 months at recommended storage temperature. Part A: ll0°F (43°C) Part B: 130°F (54°C) Part C: 102°F (39°C) Paint products contain chemical ingredients which are considered hazardous. Read container label warning and Material Safety Data Sheet for important health and safety information prior to the use of this product. Keep out of the reach of children. © November 1997. by Theme( Company, inc. '1 76 .,aLPPI,ICATION COVERAGE RATES MIXING POT LIFE TfilNNING SURFACE TEMPERATURE APPLICATION EQUIPMENT CLEANUP Dry Mils Wet Mils Sq Ft/Kit (mz/Kit) (Microns,~ (Microns) Large Kit Small Kit Suggested 1.5 (40) 2.0 (50) 2294 (213.3) 572 (53.1) Minimum 1.0 (25) 1.5 (40) 3440 (320.0) 857 (79.6) Maximum 2.0 (50) 3.0 (75) 1720 (160.0) 430 (40.0) Allow for overspray and surface irregularities. Film thickness is rounded to the nearest 0.5 rail or 5 microns. Application of coating below minimum or above maximum recommended dry film thicknesses may adversely affect coating perforn~ance. Note: Add Part C Accelerator according to the following chart. Temperature Range Amount of Part C 40°F to 70°E (4°C to 21°C) Full amount supplied (8 oz or 235 mL) 70°F to 80°F (21°C to 27°C) 50% of amount supplied (4 oz or 120 mL) Above 80°F (27°C) 25% of amount supplied (2 oz or 60 mL) Large Kit: Pour both gallon containers of Part A into a clean container large enough to hold all three components. Add Part C Accelerator to Part A while under agitation. 3/Iix thoroughly. Add Part B to the mbcture of Part A and Part C while under agitation. Continue agitation until all three components are thoroughly mLxed. ~ Small Kit: Add contents of the plastic b. ottle marked Part C Accelerator to Part A while under agitation. Mbc thoroughly. Add contents of the qGart can marked Part B to the mixture of Part A and Part C while under agitation. Continue agitation until all three components are thoroughly mixed. Do not use mLxed material beyond pot life limits. Part B is moisture-sensitive and will react with atmospheric moisture. Unused material must be kept tightly closed at all times. Part C Accelerator is not for use in Endura-Shiekl or other Tnemec urethane products. 2 hours at 77°F (25°C) 30 minutes at 100°F (38°C) Note: See chart at the beginning of Mixing instructions. Use No. 2 ThinneE For air spray, thin 10% or 3~ pint (380 mL) to 20% or 11/_, pints (760 mL) per gallon. For roller or brush, thin up to 10% or 3~ pint (380 niL) per gallon. Caution! Do not add thinnet if more than thirty (30) minutes have elapsed after mixing. Thinning above 20% may adversely affect coating performance. Minimum 40°F (4°C) Maximum 12~°F (49°C) The surface should be dry and at least 5°F (3°C) above the dew point. Air Spray Gun Fluid Air Cap Air Hose Mat'l Hose Atomizing Pot Tip ID ID Pressure Pressure DeVilhiss E 78 5/16" or 3/8" 3/8" or 1/2" 70-90 psi 10-20 psi MBC or JGA (7.9 or 9.5 turn) (9.5 or i2.7 ram) (4.8-6.2 bar) (0.7-1.4 bar) Low temperatures or longer hoses require higher pot pressure. Proper atomization is necessary to obtain a s~nooth finish. Roller: Use 1/4" (6.4 ram) synthetic nap cover. Do not use medium or long nap roller covers. Brush: Recommended for sinai[ areas only. Use high quality natural or synthetic bristle brushes. Airless Spray: Not recommended. Flush and clean a[1 equipment immediately after use with the recommended thinner or xylol. WARRANTY & LIMITATION OF SELLER'S LIABIL{rY: Tnernec Company, inc. weirDais aoJy Ihot ils coatings represented heroin meet ~he fo~rnulalioo standards of Tnernec ComagnU, inc. /HE WARRANTY OESCRIBEO IN THE ABOVE PARAGRAPH SHALL BE IN LIED OF ANY OTHER WARRANTY, EXPRESSED OR IMPUEO, INCLUDING BUr NaT LIMITED tO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THERE ARE NO WARRANTIES THAT EXTEND BEYONO THE DESCRIPTION ON THE FACE HEREnD the buyer's sale and exclusive remedy against Tnernec Company, Inc, shall be for laplacemeal af lhe produd in the e'/enl a defeclive condition of the producl should be faoad la exist and the exclusive remedy shall nor have faUed its essenlial purpose as land as Toemac is willing la ~rovide comparable replacernenl product to lhe ~uyer. NO OTHER REMEDY (INCLUDING, BUT NUT LIMITED TO, INCIDENTAL OR CONSEQUENTIAL OA/MGES FOR LOST PROFITS, LOST SALES, INJURY TO PERSON OR PROPERTY, ENVIRONMENTAL INJURIES OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS} SHALL BE AVAILABLE TO THE BUYER. Technical and appJicalian information heroin is provided far ~he purpose of estabUsh/ng a general profile of the coating Dad ploper cooling upplicalian procedures. [esl performance results were obtained fno controlled environmeal and Tnernec Company makes no dairn thai Ihese tests or any other tests, nccuroleiy represent oil environiDeals. As application, environmenial and design factors can vary signlficonUy, clue cure shouid be exercised in the selection and use of Ihe coating. PUBLISHED TECHNICAL UATA AND INSTRUCTIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. CONTACT YOUR TNEMEC ~EPRESENrA[IVE FOR CURRENT TECHNICAL BATA AND INSTRUCTIONS FOR INDUSTRIAL USE ONLY. TNEMEC COMP,~NY iNC3RPORUED PRINTED IN USA 6800 CORPORATE DRIVB, ~(ANSAS CITY, MISSOURI 64120-I 372 TEL: 816 483-3400 76 T N E M E GOLOR GUIDE TO SYMBOLS: 5 -Select colors and products are ANSI/NSF certified for potable water* pz-AIso available as 1255 Beige primer ® -Deeptone color- higher price group in selected products p2-Also available as 1211 Red primer White WH01 Cumulus EN01 Bare Beige PAO3 Ice Cream PAl2 C;oud AA14 LRV 88.2% LRV 80.7% LFIV 732% LRV 80.0% LRV 76.0% Tank White ~) WH02 Beige/~ ~) YB38 Steel Blue GI~t Chowder YB04 Warm Sun EN03 LRV 82.9% LRV 66.4% LRV 4t .8% LRV 70.1% LRV 784% Teardrop GB13 Delft Blue 0 GB03 Fountainbleu GB04 ClearSky EN17 . LRV 69.6% LRV 60.0% LRV 51.2% LRV 40.3% Aqua Sky GB36 ,.SMety Green ® SCO7 Batety Blue ® SC06 Indigo ® PL10 .[JiV 713% LRV 279% LRV 17.8% LRV 11.7% Daiquiri Ice PA30 G~ EN07 Balsam EN09 Malachite ® PL19 LRV 72~6% LRV 31 9% LRV 14.2% LRV 15.1% Barbados PA24 Desert Bands ENG4 Twine YB31 LRV 73.1% LRV 51.4% LRV 42.7% : : Amber Canyon SafetyYellow ~, SC01 LRV54.8% BrightYellow ® SC02 LRV 44.1% Safety Orange ~ SC03 LRV 29.6% InternationaiOrange (.~ SC04 LRV 17.8% SafetyRed® SC09 LRV15.1% Safe{y Purple ~) SC08 LRV 17.3% EN10 Weathered Bark EN05 LRV 32.6% LRV 11.9% No. 312 Med. Bronze IN02 No. 313 Dark Bronze IN03 Terra Cotta EN13 (Anodized Aluminum) LRV 9.3% (Anedized Aluminum) LRV 6.9% LRV 1 t.8% Monterrey Tile ,b2 ~) SC05 Wild Catl~il YB07 LRV 8.9% LRV 75% LRV60.8% (ANSI ZSS.1-R1973) LRV 44.6% .1N-°F~16;73) LRV 33.1% *Consult NSF or your Tnernec representative for a complete listing of certified products. WARRANTY STATEMErtT: For warranty limitation of TNEMEC COMPANY, INC. seller's liability and further product information on Tnemec products, please refer to the Tnemec product PO BOX 411749 KANSAS CITY, MISSOURI 64141-1749 data sheets, or contact your Tnemec representative. (816) 483-3400 FAX: (816) 483-3969 GR28 Black IN06 LRV 13.2% LRV 4.6% Colon sheton are representations of actual standanls a~d g~ll in ftppearance ue to pro uct, texture ~arlatlot.mv,~; level ap lication method and thick- eolo~ ~ require additional coats or a similar eolared .Rr.'ntfr' to axhieve opaci . Largen swatches of lndi~idsud colors are availa~Te an request.