The URL can be used to link to this page

Townhomes Phase 2-SP131010SUBMITTAL Main St Ph 2 Coppell, TX RKM 1805 Royal Lane Ste. 107 Dallas, TX 75229 Craig Danklefs Submitted By: craig.danklefs@ferguson.com Email: FergusonWaterworks(P)817-267-3900 2650SouthPipelineRd(F)817-267-3912 Euless,TX76040www.ferguson.com WATER SECTION PVC PIPE -C900 PVC PIPE TAPPING SLEEVE -8X8 TAPPING SLEEVE VALVES -GATE VALVES -VALVE BOXES C153 FITTINGS -C153 COMPACT DI FITTINGS -MECH JOINT RSTRNTS F/ PVC -8 MIL BLACK POLY WRAP F/ DI FIRE HYDRANT -SUPER CENTURION SERVICE BRASS -COPPER TUBE -SERVICE BRASS -METER BOX PVC PIPE C900 PVC PIPE - C900: PVC Pressure Pipe SPECIFICATION DATA Diamond (C900) PVC Pipe (4 through 12) is made of 12454 compound per ASTM D1784, in accordance with the dimensional, chemical, and physical requirements of AWWA C900. Diamond (C900) PVC Pipe bears the mark of NSF, International (NSF), the listing of Underwriters Laboratory, Inc. (UL), and (DR14 & DR18) bears the listing of Factory Mutual(FM). Diamond (C900) PVC Pipe utilizes a gasket, per ASTM F477, to seal the integral bell socket to the spigot of the next joint (which conforms to the requirements of ASTM D3139.) Each male end is beveled to facilitate joint assembly, and the spigot is referenced marked to ensure proper insertion d in the joining process. Diamond C900 is supplied in 20 foot laying lengths. Factory Mutual Systems APPROVED Physical Properties of PVC 12454: Property ASTM Minimum Test Specific Gravity D792 1.40 Tensile Strength, psi D638 7,000 Tensile Modulus, psi D638 400,000 IZOD Impact Strength D256 .65ft., lb./in. SHORT FORM Specification for Diamond C900 PVC Water Pipe Diamond C900 PVC Water Pipe shall be made of compounds conformin00 shall meet all the dimensional, chemical, and physical requirements as outlinedoints shall meet the requirements of ASTM D3139 and shall be formed using Rieber Tech Potable water pipe shall be manufactured from National Sanitatio Corporate Headquarters 1212 Johnstown Road P.O. Box 1608 6 page six Reiber Joint Illustration DC B A Extreme Testing Conditions C900 PVC pressure pipe, available in pressure ratings for a wide range of water transfer applications (Available in sizes from 4" through 12") Tough TM C900 AWWA C900 SPECIFICATION DATA Nominal Outside Diameter Bell Diameter ApproximateSpigotC900 DR-14C900 DR-18C900 DR-25 Pipe ABBell Depth CInsert MinimumMinimumMinimum SizeInches (mm)InchesInchesMark DWall (t)Wall (t)Wall (t) Inches Inches (mm)Inches (mm)Inches (mm) 4 (100) 4.800 (121.9) 6-1/2 6 5 0.343 (8.71) 0.267 (6.78) 0.192 (4.88) 6 (150) 6.900 (175.3) 9-1/4 6.5 6 0.493 (12.52) 0.383 (9.73) 0.276 (7.01) 8 (200) 9.050 (229.9) 11-3/4 7 6.5 0.646 (16.41) 0.503 (12.78) 0.362 (9.19) 10 (250) 11.100 (281.9) 14-1/4 7.5 7 0.793 (20.14) 0.617 (15.67) 0.444 (11.28) 12 (300) 13.200 (335.3) 16-3/4 8 7.5 0.943 (23.95) 0.733 (18.62) 0.528 (13.41) Possession of this page does not constitute an offer of sale Corporate Headquarters 1212 Johnstown Road P.O. Box 1608 7 page seven Product Description: AWWA C-900 Municipal Water Pipe North American Pipe's AWWA C-900 PVC product line is manufactured to meet the needs of modern municipal water distribution systems. With top quality raw materials and modern processing technology North American Pipe's C-900 pipe meets all industry standards in addition to our own rigorous quality control standards. North American Pipe’s C-900 pipe utilizes Reiber style gaskets throughout the entire product offering. North American Pipe produces a full range of CIOD pipe in DR-14, DR-18, and DR-25 classifications. Whether specifying or installing our pipe you can be assured that North American Pipe will provide the pipe “Right, On Time, All the Time”. This product is made in accordance with the following specifications: AWWA C900 ASTM D1784 ASTM D3139 ASTM F477 ANSI/NSF 14 ANSI/NSF 61 PPI TR-3 UL 1285 FM 1612 Short Form Specification for North American Pipe Corporation AWWA C-900 Municipal Water Pipe Water main distribution pipe shall be made in accordance with AWWA C900 from a compound conforming to a cell classification of 12454 as defined by ASTM D1784. Integral bells shall incorporate gaskets meeting the requirements of ASTM F477 and be locked into the bell. The assembled joint shall meet the requirements of ASTM D3139. The laying length of the pipe shall be 20 feet. The pipe and gasket must be tested and approved for contact with potable water in accordance with ANSI/NSF 61. The pipe and gasket shall be listed by Underwriters Laboratory and approved by Factory Mutual. Rev: 08/2006 AWWA C-900 Municipal Water Pipe OUTSIDE*APPROX.**APPROX.INSERT NOMINAL DIA. – NOM. BELL DIA. BELL DEPTH MARK PIPE SIZE (OD) (BD) (C) (L) 4”4.806.506.113.88 6”6.909.257.345.13 8”9.0511.759.086.13 10”11.1014.259.756.63 12”13.2016.7511.027.38 PC 100 PC 150 PC 200 NOMINAL DR 25 DR 18 DR 14 PIPE SIZE (T)(T)(T) 4”.192.267.343 6”.276.383.493 8”.362.503.646 10”.444.617.793 12”.528.733.943 Note: These dimensions are for estimating purposes only * Dimension given for Approx. Bell Diameter (BD) is for highest pressure class ** Nominal depth, depth will vary by pressure class Rev: 08/2006 TAPPING SLEEVE -8X8 TAPPING SLEEVE Water and Industrial 665 Stainless Steel Tapping Sleeve 4Ò - 24Ò Pipe Sizes with Outlets thru 12Ò Product Specifications Test Plug: Flange: 3/4” bronze with square head. 18-8 Type 304 Stainless Steel Gasket &Bridge Plate: AWWAC207 Class D (ANSI 150# NSF61, 1/4” thick, gridded Nitrile (Buna- drilling), recessed for tapping valve N), compounded to resist natural gas, per MSS-SP60. water, oil, acids, alkalies, most (aliphatic) hydrocarbon fluids and many chemicals. Body, lugs and neck: Temperature Range: -20ºFto +180ºF. 18-8 Type 304 Stainless Steel. The gasket provides 360º pipe coverage Washers: with the neck gasket molded in place in Type 304 Stainless Steel and nylon, the one-piece top half. one of each per bolt. The bridge plates are heavy gauge 302 Bolts and Nuts: Stainless Steel, recessed and molded 18-8 Type 304 Stainless Steel with into the gasket. This provides a contin- NCthreads, epoxy coated. uous smooth surface to bridge the gap Nuts are fluoropolymer coated to between body halves. prevent galling. Features: Certified to NSF/ANSI 61-G. ® Easy to install. Range helps reduce inventory. Removable bolts can easily be replaced. Meets applicable AWWAC223 Standards. Molded-in ring in the gasket to ensure effective sealing. Nylon washers provide to imrpove bolt torque capability. Heavy gague, all-stainless steel body for rugged performance. Fully chemically passivated for maximum corrosion protection. Test outlet to allow hydrostatic pressure test before tapping the pipe. 360º seal provides maximum support and reinfocement around the pipe in case of pipe break. Body drawn out to accept the outlet neck adding to the overall strength of the area under the most stress. Nominal Pipe Size*Working Pressure*Test Pressure 6”-12”150 PSI225 PSI 14”140 PSI210 PSI 16”125 PSI187 PSI 20”100 PSI150 PSI 24”75 PSI112 PSI *Depends on flange and pipe diamter. The allowable working pressure of a pipe repair clamp decreases as pipe diameter increases(regardless of manufacturer). For a particular installation, the allowable working pressure will be determined by the size of pipe, type of pipe, type of clamp, type and extent of damage, service conditions, environmental conditions, and installation workmanship. 1 Product Specifications : SPECIFICATION The tapping sleeve body and neck shallThe gasket shall be 1/4" thick and grid- be made of heavy 18-8 Type 304 stainlessded. The top half gasket shall be one-piece steel.with a molded outlet ring to ensure effective The flange shall be 18-8 Type 304 stain-sealing. It shall be NSF 61 Nitrile (Buna N) less steel, AWWAC207 Class D (ANSI150#compounded to resist: water, oil acids, alka- drilling) and recessed to accommodate tap-lies, most (aliphatic) hydrocarbon fluids and ping valves.many other chemicals. The gasket shall have The bolts shall be 18-8 type 304 stainlessa temperature range of -20ºF to +180ºF. steel with NC threads and epoxy coated. TheThe gasket shall have bridge plates nuts shall be 304 stainless steel, fluoropoly-made of heavy 302 stainless steel. The mer coated to prevent galling. One 304 stain-bridge plates shall be recessed and bonded less steel and one nylon washer to be provid-into the gasket. ed with each bolt. A¾" test outlet and plugAll welded stainless steel surface areas shall be provided to allow hydrostatic testingshall be fully passivated for maximum corro- of the seal prior to making the tap. sion protection. The plug shall be ¾" bronze with aThe tapping sleeve shall be NSF 61 list- square head. ed and meet applicable AWWAC223 stan- The tapping sleeve shall be a Smith-Blair, Inc. style 665 or approved equal. Approved By Name: Title: Date: T. HESEPRODUCTSPECIFICATIONSWERECORRECTATTIMEOFPUBLICATION M. ATERIALSPECIFICATIONSARESUBJECTTOCHANGEWITHOUTNOTICE SBCC-620. VS-B' EECATALOGROCHUREFORMOREDETAILSISITMITHLAIRS .-.. WEBSITEATWWWSMITHBLAIRCOMTODOWNLOADTHEMOSTCURRENTINFORMATION Ph: 870-773-5127 • Fax: 870-773-5212 • www.smith-blair.com Toll-Free Numbers: Ph: 800-643-9705 • Fax: 800-648-6792 30 Globe Ave, Texarkana, AR 71854 • POBox 5337, Texarkana, TX75505 2 VALVES -GATE VALVES -VALVE BOXES 29U-Domestic Cast Iron Curb, Service & Valve Boxes Plus Components Revised 01/10 SUBMITTAL (Current Revisions for All Standards Apply) SIZES: ............................Adjustable Slip and Screw type with 72, not including risers and extensions. Note: See catalog or website for complete listing of components STANDARDS: .................Produced in accordance with and meet all applic A-48 and are cast with 35B class cast iron. When properly instal Association of State Highway and Transportation Officials (AASHT rating. INSTALLATION: .............Per AWWA M44, Manual of Water Supply Practices COATING: ......................The bituminous coating is applied by the d mately 1.0 to 1.5 mils. For 4 to 12 Valves For 4 to 12 Valves For 3 to 20 Valves For 4 to 12 Valves 5¼ Shaft, Screw Type 5¼ Shaft, Slip Type 5¼ Shaft, Screw Type5¼ Shaft, Slip Type 7126 SLIP TYPE 6850 SCREW TYPE 6860 SCREW TYPE 6855 SLIP TYPE VALVE BOX VALVE BOX VALVE BOX VALVE BOX Cast Iron - 2 pieceCast Iron - 3 piece Cast Iron - 2 piece Extension Components Height Extension Extension Extension Components Height Components) Height Components Height 10T + 12B 27-37 10T + 24B 27-32 10T + 18B 33-42 10T + 24B 27-32 NOTE: with these Tops NOTE: Order Separately For ½ to 2 Curbstops 6500 SCREW TYPE T = Top CURB / SERVICE BOX B = Bottom Extension Componets In Inches EXT = Extension 18T & 27B 30-42 *Enlarged Base Available www.tylerunion.com C153 FITTINGS -C153 COMPACT DI FITTINGS -MECH JOINT RSTRNTS F/ PVC -8 MIL BLACK POLY WRAP F/ DI 44444444444444444444444A C153/A21.53 Compact Revised 01/10 DOMESTIC SUBMITTAL (Current Revisions for All Standards Apply) SIZES: ............................2 through 48 (2 Not Referenced i STANDARDS: .................ANSI/AWWA C153/A21.53-06 and NFPA 3-12 UL Lis Note: Cast with tested and traceable ASTM A536 Ductile Iron PRESSURE RATING: .......2- 24 rated @ 350 PSI; 30- 48 & all fittings with Flanged br Note: With use of special flange gasket 2-24 flanged fittings can b For 350 psi flange joint applications, we recommend the use of a gasket or comparable. Note: Compact Wyes over 12 are not pressure rated. Contact manu in your application. DEFLECTION: .................Upon completion of installation, Mechanical Joi mum of 5° deflection and 1448 a maximum of 3° deflection NSF-61: .........................Meets all requirements, UL Registered ( BITUMINOUS COATING: ......................ANSI/AWWA C104/A21.4-08 CEMENT LINING: ..........ANSI/AWWA C104.A21.4-08, Double cement lining available EPOXY COATING:..........ANSI/AWWA C116/A21.16-09 Note: Epoxy coated fittings are available to the specification required for your application(s) BARE: .............................Available BOLTS: ...........................ANSI/AWWA C111/A21.11-7 INSTALLATION: .............Per AWWA C600-99 using pipe conforming to ANSI/AWWA C151/A21.51-02 JOINT DIMENSIONS IN INCHES BOLTS Size A Dia. B C Dia. D Dia. F Dia. J Dia. K Dia. K Dia. L M S T X Size No. 12 3 3.96 2.50 4.84 4.94 4.06 6.19 7.62 7.69 .58 .62 .39 .33 ¾ Á x3 4 4 4.80 2.50 5.92 6.02 4.90 7.50 9.06 9.12 .60 .75 .39 .34 Â ¾x3½ 4 6 6.90 2.50 8.02 8.12 7.00 9.50 11.06 11.12 .63 .88 .43 .36 Â ¾x3½ 6 8 9.05 2.50 10.17 10.27 9.15 11.75 13.31 13.37 .66 1.00 .45 .38 Â ¾x4 6 10 11.10 2.50 12.22 12.34 11.20 14.00 15.62 15.62 .70 1.00 .47 .40 Â ¾x4 8 12 13.20 2.50 14.32 14.44 13.30 16.25 17.88 17.88 .73 1.00 .49 .42 Â ¾x4 8 14 15.30 3.50 16.40 16.54 15.44 18.75 20.31 20.25 .79 1.25 .55 .47 Â ¾x4½ 10 16 17.40 3.50 18.50 18.64 17.54 21.00 22.56 22.50 .85 1.31 .58 .50 Â ¾x4½ 12 18 19.50 3.50 20.60 20.74 19.64 23.25 24.83 24.75 1.00 1.38 .68 .54 Â ¾x4½ 12 20 21.60 3.50 22.70 22.84 21.74 25.50 27.08 27.00 1.02 1.44 .69 .57 Â ¾x4½ 14 24 25.80 3.50 26.90 27.04 25.94 30.00 31.58 31.50 1.02 1.56 .75 .61 Â ¾x5 16 30 32.00 4.00 33.29 33.46 32.17 36.88 39.12 39.12 1.31 2.00 .82 .66 1¿ 1x6 20 36 38.30 4.00 39.59 39.76 38.47 43.75 46.00 46.00 1.45 2.00 1.00 .74 1¿ 1x6 24 42 44.50 4.00 45.79 45.96 44.67 50.62 53.12 53.12 1.45 2.00 1.25 .82 1À 1¼x6½ 28 48 50.80 4.00 52.09 52.26 50.97 57.50 60.00 60.00 1.45 2.00 1.35 .90 1À 1¼x6½ 32 www.tylerunion.com FIRE HYDRANT -5-1/4 FIRE HYDRANTS SERVICE MATERIAL COPPER TUBE - -SERVICE BRASS -METER BOX ® MUELLERBR2B SERIES BRONZE 4.8 SERVICE SADDLES - DOUBLE STRAP Rev. 9-09 MUELLER®Service Saddles for use on A-C, cast iron, ductile iron Outlet tapped with either AWWA taper (C.C.) or AWWA I.P. thread For use on A-C pipe, cast iron or ductile iron pipe and cast iro 200 psig (1379 kPa) maximum working pressure Available in double strap designs Brass body Flattened silicon bronze straps Rolled strap threads O-ring sealed outlet 3/4" thru 2" tap sizes (5/8" some styles) Meets all applicable parts of ANSI/AWWA C800 NSF 61 Certiﬁed BR 2 B Series ® MUELLERService Saddles with Bronze Double Straps Pipe O.D. Range*Kind and Size of PipeBronze Double Straps Size of Tapping Base(add to "Base" to complete catalog number) Cast or Tap*** InchmmA-CCatalog Ductile IronThread 5/8"3/4"1"1-1/4"1-1/2"2" Number 4.74-5.32121.0-135.04"CC or IPBR2B0474062075100--- 4.74-5.10121.0-129.44"CC or IPBR2B0474---125150200 5.10-5.60129.4-142.24"CC or IPBR2B0510---125150200 6.84-7.45174.0-189.06"CC or IPBR2B0684062075100125150200 8.99-9.67229.0-245.08"CC or IPBR2B0899062075100125150200 11.04-12.12281.0-307.010"CC or IPBR2B1104062075100125150200 ** 13.14-14.58334.0-370.012"CC or IPBR2B1314062075100125150200 15.22-16.88386.6-428.714"CC or IPBR2B1522-075100-150200 17.32-19.19439.9-487.416"CC or IPBR2B1732-075100-150200 18.00-19.50457.2-495.318"CC or IPBR2B1800-075100125150200 20.00-24.30508.0-624.820"CC or IPBR2B2000-075100125150200 24.00-25.80609.6-655.324" CC or IPBR2B2400-075100125150200 *A-C pipe, classes 150-200 per ASTM C295 and AWWA C400 actual sted in the preceding charts. Centrifugally cast pipe, classes 50-250 per ANSI/AWWA C102/A21.2; ANSI/AWWA C106/A21.6; ANSI/AWWA C108/A21.8, and Federal speciﬁcation WW-P-421. Ductile iron pipe, classes 50-56 per ANSI/AWWA C151/A21.51; Cast iron O.D. PVC plastic pipe per AWWA ** The outside diameter of A-C pipe varies from manufacturer to Determine the O.D. of the pipe at the point of saddle installation;2) From the pipe O.D. range column of the above chart, choose a d pipe diameter. ***CC=AWWA Taper; IP=AWWA IP thread (F.I.P.T) The 5/8" tap is available in CC thread only for a Stainless Ste These machines may be used with the service saddles illustrated on this page MachineService Saddle Tap Size 5/8"3/4"1"1-1/4"1-1/2"2" E-5XX X -XX D-5-XXXXX TRU-CUT-XX--- MEGA-CUTXXX--X PL-2-XX--- TO ORDER SPECIFY QUANTITY, OUTLET TAPPING SIZE AND CATALOG NUMBE Use on A-C pipe, which contains a known carcinogen, requires app 5.9 1/2" - 2" GROUND KEY DESIGN CORPORATION VALVES Shaded area indicates changes Rev. 9-09 Ground Key Corporation Valve Ground Key Corporation Valve Inlet: AWWA taper Inlet: AWWA I.P. thread (MUELLER CC) thread ® Outlet: MUELLER ® Outlet:MUELLER® INSTA-TITEConnection for ® INSTA-TITEConnection for CTS PE tubing* H-15006 H-15024 CTS PE tubing* Ground Key Corporation Valve Ground Key Corporation Valve Inlet:AWWA taper Inlet:AWWA I.P. thread (MUELLER CC) thread Outlet: MUELLER Outlet: MUELLER INSTA-TITE Connection for INSTA-TITE Connection for H-15026 IPS PE pipe* H-15005 IPS PE pipe* Ground Key Corporation Valve Ground Key Corporation Valve Inlet: AWWA taper Inlet: AWWA I.P. thread (MUELLER CC) thread Outlet Outlet connection H-15000 H-15025 connection 5/8"1/2"5/8" x 3/4"3/4"3/4" x 1"1" 1"x1-1/4" 1-1/4"1-1/2"1-1/2"x2"2" Ground Key Corporation Valve Ground Key Corporation Valve Inlet: AWWA I.P. thread Inlet: AWWA taper Outlet (MUELLER CC) thread bend connection Outlet H-15010 H-15035 bend connection Ground Key Corporation Valve Ground Key Corporation Valve Inlet: AWWA taper Inlet: AWWA I.P. thread (MUELLER CC) thread Outlet Outlet bend connection bend connection H-15045 H-15020 5/8"x3/4"3/4"3/4"x1"1"1-1/2"2" *See charts on pages 5.12-5.16 for tubing and pipe that may be u Requires minimum ordering quantity. Contact MUELLER Customer S Technical Data: 7-04 tube Cerro tube is the original copper tube for plumbing, air conditi refrigeration applications in residential, commercial and instit installations. We provide a complete range of sizes and types, e to exact specifications to meet the highest standards of perform ProductCodeUsesSpecifications TemperLengths ASTM B88 Copper HardGreenDomestic water 10 ft. straight Water Tube,20 ft. straightservice and Type K distribution, fire (heavy wall)Softprotection, solar, 20 ft. straight 40 ft. coilsfuel/fuel oil, HVAC, snow melting, 60 ft. coils compressed air, 100 ft. coils natural gas, Typical uses include: liquefied petroleum ¥ Type M - above ground residential and light (LP) gas, vacuum commercial uses. (Sizes range from 3/8" - 8" Copper BlueDomestic waterASTM B88 Hard10 ft. straight diameter) Water Tube,service and 20 ft. straight ¥ Type L - residential and commercial uses. Type L distribution, fire (Sizes range from 1/4" - 8" diameter) (medium wall)protection, solar, Soft20 ft. straight fuel/fuel oil, HVAC, 30 ft. coils ¥ Type K - underground residential, commercial 40 ft. coilssnow melting, and industrial uses. (Sizes range from compressed air, 60 ft. coils 1/4" - 8" diameter) natural gas, 100 ft. coils liquefied petroleum ¥ Type DWV - ASTM B306: used for drainage, (LP) gas, vacuum waste and vents ASTM B88 Copper Hard10 ft. straightRedGeneral plumbing Water Tube,and heating purposes; 20 ft. straight Type M drainage waste, (light wall)vent and other light pressure uses. ASTM B306 Copper Hard10 ft. straightYellowDrainage waste, Drainage vents, soil and other 20 ft. straight Tube,non-pressure Type DWV applications Copper UNS No. C12200 Types K, L, and M ASTM B88 Color marking is not applicable to tube furnished in annealed st lengths or coils. Corporate Headquarters PO Box 66800 ¥ St.Louis,MO 63166-6800 888-237-7611 |618-337-6000 ¥ f.618-337-6958 www.cerroflow.com SUBMITTAL INFORMATION 70 Series Coppersetter - (VBB77-xxB-11-77 style) ANGLE BALL VALVE BY ANGLE BALL VALVE (2" METER) FEMALE IRON PIPE THREAD INLET AND OUTLET Angle BallAngle Ball 17" Meter Spacing Meter ValveMeter Valve Meter Support Bracket Height 2" Bypass Ball ValveCopper Tube 1-1/4" FIP Inlet Brace Eye FIP Outlet 28-3/4" S L C A. S ERVICEINEONNECTION PPROX UBMITTED HC N EIGHTATALOGUMBER FIP IFIP OW. L. I() NLETUTLETTBS TEMS 8"32VBB77-8B-11-77 12"34VBB77-12B-11-77 15"35VBB77-15B-11-77 2"2"18"36VBB77-18B-11-77 21"37VBB77-21B-11-77 24"38VBB77-24B-11-77 27"39VBB77-27B-11-77 FEATURES • All brass conforms to AWWA Standard C800 (ASTM B-62 and ASTM B-584, UNS NO C83600 - 85-5-5-5) • Constructed with Type K Copper, and conforms to ASTM B-88, Copper Alloy #122. • All Ford Meter Setters are assembled with lead-free solder. • Bracing Eyes are standard. • Meter Support Brackets are standard. • Optional High Bypass - add "HB" following the height. Example: VBB77-12HB-11-77. • Padlock wing is standard on all Angle Meter Ball Valves or Key Valves. • Outlet ball valve may be used as customer shut-off up to 300 PSI The Ford Meter Box Company considers the information in this submittal form to be correct at the time of publication. Item and option availability, including specifications, are subject to change without notice. Please verify that your product information is current. Submitted By: The Ford Meter Box Company, Inc. P.O. Box 443, Wabash, Indiana U.S.A. 46992-0443 Phone: 260-563-3171 / Fax: 800-826-3487 Overseas Fax: 260-563-0167 http://www.fordmeterbox.com 11/08/12 COPPER METER YOKES WITH 8A.1 HORIZONTAL INLET AND OUTLET Rev. 8-04 Multi-purpose thread ends Typical installation of a horizontal inlet and (H-1405 shown) outlet copper meter yoke. Copper meter yokes with horizontal inlet and outlet and multi - CatalogH-1400H-1401H-1404H-1405B-2404B-2405 number Description Plain yokeWith test valveWith lock wingWith lock wingWith lock wingWith lock wing ground keyground key MUELLER 300™MUELLER 300™ angle meterangle meterAngle Ball ValveAngle Ball Valve stopstop and testand test valve valve Check valve options MUELLER Copper Meter Yokes can be ordered with one of the follow an ASSE approved top entry vertical check valve; an ASSE approve check valve; a dual check valve (ASSE non-approved). To order th approved top entry check feature, add a sufﬁx of -6A to the yoke cataloge - 6D number; add for the same check with a test drain. For the dual check feature, add a sufﬁx of 2A to the yoke catalog number for the ASSE ap- -2 sufﬁx for the nonapproved model. Examples: proved model or Angle dual check H-1404-6D for the ASSE approved top entry vertical check with a test drain TM M-98ASSE valve H- 1404-2A for the ASSE approved model angle dual check valve. approved top entry vertical check valve Dimensions Metersize5/8"5/8"x3/4"*3/4"*1"* NominalsizeofI.P.threadinmeternut3/4"1"1"1-1/4" DimensionA1-1/16"1-5/16"1-5/16"1-5/8" DimensionB7-7/8"7-7/8"9-5/16"11-1/16" DimensionC-nominalpipesize3/4"3/4"3/4"1" ofinletandoutlet DimensionD7-15/16"7-15/16"9-3/8"11-1/8" DimensionE12-5/8"12-5/8"14-1/4"17-1/4" DimensionF-minimumriserheight7" (9"**)7"(9"**)8"(10"**)10"(12"** 9",12",15",18",9",12",15",18",12",15",18",21",12",15",18",21", Otherriserheightsavailable21",24",27",30",21",24",27",30",24",27",30",33",24",27",30",33", 33",and36"33",and36"and36"and36" * Add R to the end of the *Add "R" to the end of the yoke cata 5/8x3/4x7 B-2404R. ** Minimum with 6A or 6D option. Copper Meter Yokes are normally supplied less end connections. See pages 8A.48 and 8A.49 for end connections that can be used wi Note: the 5/8", 5/8" x 3/4", and 3/4"sizes are furnished with a SPECIFY METER SIZE, RISER HEIGHT AND CATALOG NUMBER. UNITWILLBESUPPLIEDPERCITYOFCOPPELLSPECIFICATIONS SEWER SECTION PVC PIPE & FITTINGS -SDR 35 PVC PIPE -SEWER FITTINGS MANHOLES -MANHOLES -RING AND COVER Sani-21: TM PVC Sewer Pipe SANITARY SEWER PIPE FOR THE 21st CENTURY SPECIFICATION DATA D3034 & F679 SEWER SPECIFICATION DATA Diamond gravity sewer pipe 4 inches through 48 inches shall be made of compounds conforming to material requirements of ASTM D3034 and ASTM F679 in accordance with ASTM D1784. Diamond PVC Sewer Pipe meets all the dimensional, chemical, and physical requirements as outlined in ASTM D3034 and ASTM F679. The pipe sizes 4 inches through 48 inches are made with an integral bell water-tight joint that meets the requirements of ASTM D3212 and that utilizes a Rieber gasket system for sealing that meets the requirements of ASTM F477. Each male end shall be beveled to facilitate joining and referen insertion depth. Diamond furnished lubricant is to be used in th Physical Properties of ASTM D3034 & F679 Pipe Stiffness Pipe Materials: Pipe Modulus Pipe shall be made of PVC plastic having a minimum cell SDR E = 400,000 E = 500,000 classification of 12454 or 12364 as defined in Specification 41 28 35 D1784. 35 46 57 Property ASTM Minimum 26 115 144 Test Specific Gravity D792 1.40 Standard laying lengths are 14 and 22 feet Tensile Strength, psi D638 7,000 Tensile Modulus, psi D638 400,000 IZOD Impact Strength, D256 .65ft., lb./in. SHORT FORM Specification for Diamond PVC Solid-Wall Sewer Pipe SDR 26 or S Diamond PVC Solid-Wall Sewer PIpe shall be made of compounds con requirements of ASTM D3034 or ASTM F679. Diamond PVC Sewer Pipe as outlined in ASTM D3034 orASTM F679. Diamond PVC Sewer Pipe shall be instameet the requirements of ASTM D3212 and shall be formed using Rieber Techs. Corporate Headquarters 1212 Johnstown Road P.O. Box 1608 page 13 thirteen Sani-21: PVC Sewer Pipe SPECIFICATION DATA TM SANITARY SEWER PIPE FOR THE 21st CENTURY Reiber Joint Illustration DC B A Sani-21 is supplied in 14 foot and 22 foot laying lengths. Strength Sani-21 D3034 & F679 SEWER SPECIFICATION DATA Nominal OutsideBell SocketSocketInsertWall ThicknessWall Thickness Standard laying lengths are 14 & 22 feet Pipe SizeDiameter ADiameter BDepth CMark DSDR26/PS115 SDR35/PS46 InchesInchesInchesInchesInches(t) Inches(t) Inches D-3034 Pipe Dimensions 4 4.215 5-1/4 4-5/8 4 0.162 0.120 6 6.275 7-1/2 4-3/4 4 0.241 0.180 8 8.400 9-7/8 6-1/8 5 0.323 0.240 10 10.500 12-3/8 6-3/4 6 0.404 0.300 12 12.500 14-5/8 7-1/4 6 0.481 0.360 15 15.300 18 6-3/4 6 0.588 0.437 F-679 Pipe Dimensions 18 18.701 21-3/4 7-3/4 7 0.671 0.499 21 22.047 25-1/2 7-3/4 7 0.791 0.588 24 24.803 28-3/4 8-1/2 7-1/4 0.889 0.661 27 27.953 32-1/2 8-1/2 7-1/4 1.002 0.745 30 ciod 32.000 37-1/4 12 10 1.148 0.853 36 ciod 38.300 43-1/4 12 10 1.373 1.021 42 ciod 44.500 53 16 13 1.187 48 ciod 50.800 60 16 13 1.355 Possession of this page does not constitute an offer of sale Prices are subject to a firm policy of Price in effect at time Corporate Headquarters 1212 Johnstown Road P.O. Box 1608 page 14 fourteen Product Description: ASTM D3034 Gravity Sewer Pipe North American Pipe's ASTM D3034 Gravity Sewer PVC product line is manufactured to meet the needs of modern municipal waste water systems, residential waste water control and other non- pressure applications. With top quality raw materials and modern processing technology North American Pipe's ASTM D3034 Gravity Sewer pipe meets all industry standards in addition to our own rigorous quality control standards. North American Pipes ASTM D3034 Gravity Sewer pipe utilizes Reiber style gaskets throughout the entire product offering. North American Pipe produces a full range of ASTM D3034Gravity Sewer pipe in SDR-35 and SDR-26 classifications. Whether specifying or installing our pipe you can be assured that North American Pipe will provide the pipe Right, On Time, All the Time. This product is made in accordance with the following specificat ASTM D3034 ASTM D1784 ASTM F477 ASTM D3212 Short Form Specification for North American Pipe Corporation ASTM D3034 Gravity Sewer Pipe PVC gravity sewer pipe shall be made from a compound conforming to a cell classification of 12454 or 12364 as defined by ASTM D1784 and in accordance with ASTM D3034 for sizes four inch through fifteen inch. The wall thickness, when tested according to ASTM D3412, shall correspond to a dimension ratio of SDR 35 with a pipe stiffness value of 46 or SDR26 with a pipe stiffness of 115 for heavy wall pipe. Integral bells shall incorporate locked in gaskets meeting the requirements of ASTM D3212 and F477. The laying length of the pipe shall be 14 feet. Rev: 01/2006 ASTM D3034 Gravity Sewer Pipe OUTSIDE*APPROX.**APPROX.INSERT NOMINAL DIA. NOM. BELL DIA. BELL DEPTH MARK PIPE SIZE (OD) (BD) (C) (L) 44.2155.254.273.250 66.2757.505.404.125 88.40010.006.274.250 1010.50012.257.165.250 1212.50014.258.045.500 1515.30017.259.617.500 NOMINAL SDR 35 SDR 26 SDR 23.5 PIPE SIZE (T)(T)(T) 4.120.162.178 6.180.241.265 8.240.323 10.300.404 12.360.481 15.437.588 Note: These dimensions are for estimating purposes only * Dimsure class ** Nominal depth, depth will vary by pressure class Rev: 01/2006 MANHOLES MANHOLE - -RING AND COVER