Loading...
Duke Lesley 2RC-140526 11200 SEAGOVILLE ROAD, BALCH SPRINGS, TX 75180 214-660-3662 ACSIMILE 214-660-3626 COPPELL CONFERENCE CENTER Coppell, TX Contractor: KCK Utility Construction, Inc QUESTIONS: PLEASE CONTACT Charlie Smyth 214-475-3777 KNOWLEDGE EXPERIENCE SERVICE INDEX COPPER Cerro Flow Products SADDLES Ford Meter Box CURB STOPS/ CORPORATIONS/ COUPLINGS Ford Meter Box DOUBLE CHECK VALVES Watts METER BOXES DFW Plastics PIPE Advanced Drainage System Diamond Plastics SDR35/ DR14 SEWER FITTINGS GPK FIRE DEPT. INLET CONNECTIONS Guardian CLEANOUTS Stan Roberts Plastic G 1504 Accucast - Cast Iron 404 RUBBER COUPLINGS Fernco TAPPING SLEEVE Ford Meter Box FIRE HYDRANTS Mueller 2 GATE VALVES M&H VALVE BOXES Tyler Union RESTRAINTS AND MJ & FL FITTINGS Tyler Union IN BUILDING RISERS Watts MAN HOLES Bass & Hays Foundry 3 ADS, Inc. Drainage Handbook Specifications 1-7 ________________________________________________________________ ® ADS N-12 ST IB PIPE (per AASHTO) SPECIFICATION Scope This specification describes 4- through 60-inch (100 to 1500 mm) ADS N-12 ST IB pipe (per AASHTO) for use in gravity-flow drainage applications. Pipe Requirements ADS N-12 ST IB pipe (per AASHTO) shall have a smooth interior and annular exterior corrugations. 4- through10-inch (100 to 250 mm) shall meet AASHTO M252, Type S or SP. 12- through 60-inch (300 to 1500 mm) shall meet AASHTO M294, Type S or SP or ASTM F2306. ManningÓs ÐnÑ value for use in design shall be 0.012. Joint Performance Pipe shall be joined using a bell & spigot joint meeting AASHTO M252, AASHTO M294 or ASTM F2306. The joint shall be soil-tight and gaskets, when applicable, shall meet the requirements of ASTM F477. Gaskets shall be installed by the pipe manufacturer and covered with a removable wrap to ensure the gasket is free from debris. A joint lubricant supplied by the manufacturer shall be used on the gasket and bell during assembly. Fittings Fittings shall conform to AASHTO M252, AASHTO M294, or ASTM F2306. Bell and spigot connections shall utilize a spun-on or welded bell and valley or saddle gasket meeting the soil-tight joint performance requirements of AASHTO M252, AASHTO M294 or ASTM F2306. Material Properties Virgin material for pipe and fitting production shall be high density polyethylene conforming with the minimum requirements of cell classification 424420C for 4- through 10-inch (100 to 250 mm) diameters, or 435400C for 12- through 60-inch (300 to 1500 mm) diameters, as defined and described in the latest version of ASTM D3350, except that carbon black content should not exceed 4%. The 12- through 60-inch (300 to 15 virgin pipe material shall comply with the notched constant ligament-stress (NCLS) test as specified in Sections 9.5 and 5.1 of AASHTO M294 and ASTM F2306, respectively Installation Installation shall be in accordance with ASTM D2321 and ADS recommended installation guidelines, with the exception that minimum cover in trafficked areas for 4- through 48-inch (100 to 1200 mm) diameters shall be one foot. (0.3 m) and for 54- and 60-inch (1350 and 1500 mm) diameters, the minimum cover shall be 2 ft. (0.6 m) in single run applications. Backfill for minimum cover situations shall consist of Class 1, Class 2 (minimum 90% SPD) or Class 3 (minimum 90%) material. Maximum fill heights depend on embedment material and compaction level; please refer to Technical Note 2.01. Contact your local ADS representative or visit our website at www.ads-pipe.com for a copy of the latest installation guidelines. Pipe Dimensions Nominal Diameter, in (mm) Pipe I.D. 4 6 8 10 12 15 18 24 30 36 42 48 54* 60 in (mm) (100) (150) (200) (250) (300) (375) (450) (600) (750) (900) (1050) (1200) (1350) (1500) Pipe O.D.** 4.8 6.9 9.1 11.4 14.5 18 22 28 36 42 48 54 61 67 in (mm) (122) (175) (231) (290) (368) (457) (559) (711) (914) (1067) (1219) (1372) (1549) (1702) Perforations All diameters available with or without perforations *Check with sales representative for availability by region. **Pipe O.D. values are provided for reference purposes only, values stated for 12- through 60-inch are ± 1 inch. Contact a sales representative for exact values. ADS, Inc., October 2009 ADS, Inc. Drainage Handbook Specifications 1-8 ________________________________________________________________ ® N-12 ST IB (per AASHTO) JOINT SYSTEM (Joint configuration & availability subject to change without notice. Product detail may differ slightly from actual product appearance.) ADS, Inc., October 2009 For Fire Protection Applications Job Name Contractor Job Location Approval Approval Representative LEAD FREE Series TR Transition Risers Sizes: 4" – 10" (100-250mm) Series TR Transition Risers are used to connect the main fire supply to the building overhead fire system. The fitting passes under the foundation without joints and extends up through the TEST CAP floor. Provided with installation tabs, the unit has a CIPS (Cas Iron Pipe Size) coupler for easy connection to the underground NOW INCLUDED! supply (AWWA C900 PVC and Ductile Iron Pipe) and industry standard grooved-end connection (AWWA C606) on the building side for easy connection to the overhead fire sprinkler system. Watts Transition Risers are precision engineered and manu- factured to provide exceptional reliability and reduce instal- lation time & labor costs associated with field assembly. In accordance with NFPA 24-2007, the UL and FM approved Transition Risers replace numerous fittings, elbows & spools and reduces the possibility of leaks or failure in comparison to traditional installation methods and materials. Factory tested integrity ensures the highest quality installation. The use of stainless steel significantly increases the reliability and life TR riser. Features Building Floor Building perimeter wall position and handle the riser - identifiable for approvals lengths to meet all local requirements Flow Specification Transition Riser shall be installed as indicated on the plans. INQUIRE WITH GOVERNING AUTHORITIES Riser shall be composed of a single extended 90 degree fit- FOR LOCAL INSTALLATION REQUIREMENTS connection on the outlet (building) side and a CIPS coupler on *The wetted surface of this product contacted by consumable the inlet (underground) side. The grooved end shall include a water contains less than 0.25% of lead by weight. Coupler and Cap to facilitate testing of the underground piping. The Transition Riser shall be a Watts Series TR. Watts product specifications in U.S. customary units and metric e measurements, please contact Watts Technical Service. Watts reserves the rightns, or materials with- out prior notice and without incurring any obligation to make subsequently sold. Standards End Connections: NFPA — Designed to allow the contractor to conform to NFPA Horizontal End: Mates with Ductile Iron Pipe and AWWA Where a riser is close to building foundations, underground Utilizes Gasket conforming to UL 157 with “Lock in” fittings of proper design and type shall be used to avoid pipe gasket configuration joints being located under the foundations. NFPA — Approvals Fittings Vertical End: Meets AWWA C-606 dimensions for roll grooved pipe Meets AWWA C-207 class D for flanges Ratings Dimensions – Weights A Testing Grooved End (Flange Optional) B CIPS Coupling Tie-Rod Bracket C A Watts Water Technologies Company USA:www.watts.com Canada: www.wattscanada.ca ES-LF007 For Non-Health Hazard Applications Job Name Contractor ……………………………………………………………………………………………………………………………………………………………………………………………………………………………………… Job Location Approval …………………………………………………………………………………………………………………………………………………………………………………………………………………………………… Engineer Contractors P.O. No. …………………………………………………………………………………………………………………………………………………………………………………………………………………… Approval Representative ………………………………………………………………………………………………………………………………………………………………………………………………………………………………… LEADFREE * Series LF007 Double Check Valve Assemblies 1 Sizes: ‡" … 3" (15 … 80mm) 2 Series LF007 Double Check Valve Assemblies shall be installed at referenced cross-connections to prevent the backflow of polluted water into the potable water supply. Only those cross- connections identified by local inspection authorities as non- 3 ‡" (20mm) LF007M3QT 4 health hazard shall be allowed the use of an approved double check valve assembly. The LF007 features Lead Free* con- struction to comply with Lead Free* installation requirements. Check with local authority having jurisdiction regarding vertica orientation, frequency of testing or other installation requirem The valve shall meet the requirements of ASSE Std. 1015 and AWWA Std. C510. Approved by the Foundation for Cross- Connection Control and Hydraulic Research at the University of Southern California. 2" (50mm) LF007M1QT HC Features €Ease of maintenance „ only one cover Test Cocks €Top entry €Replaceable seats and seat discs €Modular construction €Compact design €Cast Lead Free* bronze body construction „ ‡" … 2" 1 2 (15 … 50mm) €Fused epoxy coated cast iron body „ 2‡" … 3" (65 … 80mm) 1 2 €Top mounted Lead Free* ball valve test cocks €Low pressure drop €No special tools required for servicing €‡" … 1" (15 … 25mm) have tee handles 1 2 First CheckSecond Check Module Assembly Module Assembly Specifications A Double Check Valve Assembly shall be installed at each The LF007 Series features a modular design concept which facilit noted location. The assembly shall consist of two positive seat- complete maintenance and assembly by retaining the spring load. ing check modules with captured springs and rubber seat discs. The check module seats and seat discs shall be Now Available replaceable. Service of all internal components shall be through WattsBox Insulated Enclosures. a single access cover secured with stainless steel bolts. The Double Check Valve Assemblies shall be constructed using For more information, send for literature ES-WB. Lead Free* materials. Lead Free* Double Check Valve Assemblies shall comply with state codes and standards, where applicable, requiring reduced lead content. The assem- IMPORTANT:INQUIRE WITH GOVERNING AUTHORITIES bly shall also include two resilient seated isolation valves; fo FOR LOCAL INSTALLATION REQUIREMENTS top mounted, resilient seated test cocks. The assembly shall meet the requirements of ASSE Std. 1015 and AWWA Std. *The wetted surface of this product contacted by consumable C510. Approved by the Foundation for Cross-Connection water contains less than one quarter of one percent (0.25%) of Control and Hydraulic Research at the University of Southern lead by weight. California. Assembly shall be a Watts Series LF007. Watts product specifications in U.S.customary units and metric ameasurements, please contact Watts Technical Service.Watts reserves the right or materials with- out prior notice and without incurring any obligation to make subsequently sold. Pressure „ Temperature Suffix: S - bronze strainer 1‡" … 2" (15 … 50mm) 2 LF - without shutoff valves Temperature Range: 33°F … 180°F (0.5°C … 82°C). LH - locking handle ball valves (open position) Maximum Working Pressure: 175psi (12.1 bar). SH - stainless steel ball valve handles 2 1‡" … 3" (65 … 80mm) 2 HC - 2‡" inlet/outlet fire hydrant fittings (2" valve) 1 2 140°F (60°C) intermittent. Prefix: Maximum Working Pressure: 175psi (12.1 bar). U - Union connections 2 1‡" … 3" (65 … 80mm) 2 Standards Suffix: ASSE Std. 1015, AWWA Std. C510 NRS - non-rising stem resilient seated gate valves IAPMO PS31, CSA B64.5 OSY - UL/FM outside stem and yoke resilient seated gate valves Approvals LF - without shutoff valves QT-FDA - FDA epoxy coated quarter-turn ball valves ASSE, AWWA, IAPMO, CSA, UPC Approved by the Foundation for Cross-Connection Control and Hydraulic Research at the University of Southern California. €Models with suffix LF and S are not listed. UL Classified (without shutoff valves only) ‡" … 2" 3 4 (20 … 50mm) (except 007M3LF) UL Classified with OSY gate valves (2‡" and 3" horizontal only.) 1 2 *Horizontal and vertical flow upŽ approval on all sizes Dimensions … Weights Models Sizes: 1‡" … 2" (15 … 50mm) 2 A s A C B *B s D R T F *Subscript S = strainer model 1 Suffix HC „ Fire Hydrant Fittings dimension AŽ= 23‡" (594mm) 2 Dimensions … Weights Sizes: 2 1‡" … 3" (65 … 80mm) C (open) 2 9" (229mm) 5 4‡" (109mm) 16 N R E1 E M A Strainer Dimensions 1" LFU007M1QT Union Tailpiece Union Tailpiece Union Nut Union Nut A Sizes: 1‡" … 2" (15 … 50mm) 2 Capacity As complied from documented Foundation for Cross-Connection Cont Hydraulic Research at the University of Southern California lab * Typical maximum system flow rate (7.5 feet/sec., 2.3 meters/se ** UL rated flow 1 ‡" (15mm) 1 1‡" (40mm) 2 2 * * Flow Flow 3 2" (50mm) ‡" (20mm) 4 * * Flow Flow 1" (25mm) 1 2‡" (65mm) 2 * ** * Flow Flow 1 1‡" (32mm) 3" (80mm) 4 * ** * Flow Flow 815 Chestnut St., No. Andover, MA 01845-6098; www.watts.com A Watts Water Technologies Company USA: 5435 North Service Rd., Burlington, ONT. L7L 5H7; www.wattscanad Canada: ES-LF007 0940© 2009 Watts 29U-Domestic Heavy Duty C ast Iron C urb, Service, & Valve Boxes + Components Revised 0 7/1 1 SUBMITTAL (Current Revisions for All Standards Apply) SIZES: ............................Adjustable Slip and Screw type with 9” to 72” (Lengths noted do not include the addition of risers, extension See the C atalog or List Pr i ce guide for acc ess., lids, rings, bases, risers, meter covers, etc. STANDARDS: .................Produced with Class 35 cast iron in accordance with and meet ing all applicable terms and provisions of ASTM A-48. All Tyler Union valve boxes w hen properly installed are suitable for use in conjunction with projects utilizing American Association of State Highway and Transportation Officials (AASHTO) standards and prov INSTALLATION: .............Per AWWA M44, Manual of Water Supply Practices COATING: ......................The asphaltic bituminous coating is applied to a thickness of 1.0 to 1.5 mil and the coating once dry is neither brittle when exposed to cold or stic For 4” to 12” Valves For 4” to 12” Valves For 3” to 20” Valves For 4” to 12” Valves 5¼” Shaft, Screw Type 5¼” Shaft, Slip Type 5¼” Shaft, Screw Type5¼” Shaft, Slip Type 7126 SLIP TYPE 6850 SCREW TYPE 6860 SCREW TYPE 6855 SLIP TYPE VALVE BOX VALVE BOX VALVE BOX VALVE BOX Cast Iron - 2 pieceCast Iron - 3 piece Cast Iron - 2 piece Extension Components Height Extension Extension Extension Components Height Components) Height Components Height 10T + 12B 27-37 10T + 24B 27-32 10T + 18B 33-42 10T + 24B 27-32 NOTE: with these Tops NOTE: Order Separately For ½” to 2” Curbstops 6500 SCREW TYPE T = Top CURB / SERVICE BOX B = Bottom Extension Componets In Inches EXT = Extension 18T & 27B 30-42 *Enlarged Base Available Tyler:11910 CR 492-Tyler,TX 75706-(800) 527-8478 Anniston:1-L 1- Corona:1001 El Camino Ave.-Corona, CA 92879-(866) 527-8471 Portland: 6204 N. Marine Dr.-Portland, OR 97203-(866) 527-8471 www.tylerunion.com 44444444444444444444444A C153/A21.53 Compact Revised 0 8/1 1 SUBMITTAL (Current r evisions for a ll Standards a pply) SIZES: ............................2” through 48” (2” Not Referenced i STANDARDS: .................ANSI/AWWA C153/A21.53-06 and NFPA 3”-1 6” UL Listed (EX2111) Note: Cast with tested and traceable ASTM A536 Ductile Iron PRESSURE RATING: .......2”- 24” rated @ 350 psi; 30”- 48” & all fittings with Flanged branches rated @ 250 psi Note: With use of special flange gasket 2”- 24” flanged fittings can be rated @ 350 psi For 350 psi flange joint applications, we recommend the use of a type gasket or comparable. Note: Compact Wyes over 12” are not pressure rated. Contact manufactu in your application. DEFLECTION: .................F ittings 2”- 12” *5° maximum deflection & 14”– 48” *3° maximum deflection Note: If pipe O.D. & fitting I.D. at nominal, achievable deflection imaximum NSF-61: .........................Meets all requirements, UL Listed (MH16439) ASPHALTIC COATING: ......................ANSI/AWWA C104/A21.4-08 - ANSI/AWWA C153 CEMENT LINING: ..........ANSI/AWWA C104.A21.4-08, Double cement lining available EPOXY COATING:..........ANSI/AWWA C116/A21.16-09 Note: F ittings are available to the specification(s) required for your application(s) BARE: .............................Available BOLTS: ...........................ANSI/AWWA C111/A21.11-7 INSTALLATION: .............Per AWWA C600-10 using pipe conforming to ANSI/AWWA C151/A21.51-02 or C900-C905 JOINT DIMENSIONS IN INCHES BOLTS Size A Dia. B C Dia. D Dia. F Dia. J Dia. K Dia. K Dia. L M S T X Size No. 12 3 3.96 2.50 4.84 4.94 4.06 6.19 7.62 7.69 .58 .62 .39 .33 ¾ Á x3 4 4 4.80 2.50 5.92 6.02 4.90 7.50 9.06 9.12 .60 .75 .39 .34  ¾x3½ 4 6 6.90 2.50 8.02 8.12 7.00 9.50 11.06 11.12 .63 .88 .43 .36  ¾x3½ 6 8 9.05 2.50 10.17 10.27 9.15 11.75 13.31 13.37 .66 1.00 .45 .38  ¾x4 6 10 11.10 2.50 12.22 12.34 11.20 14.00 15.62 15.62 .70 1.00 .47 .40  ¾x4 8 12 13.20 2.50 14.32 14.44 13.30 16.25 17.88 17.88 .73 1.00 .49 .42  ¾x4 8 14 15.30 3.50 16.40 16.54 15.44 18.75 20.31 20.25 .79 1.25 .55 .47  ¾x4½ 10 16 17.40 3.50 18.50 18.64 17.54 21.00 22.56 22.50 .85 1.31 .58 .50  ¾x4½ 12 18 19.50 3.50 20.60 20.74 19.64 23.25 24.83 24.75 1.00 1.38 .68 .54  ¾x4½ 12 20 21.60 3.50 22.70 22.84 21.74 25.50 27.08 27.00 1.02 1.44 .69 .57  ¾x4½ 14 24 25.80 3.50 26.90 27.04 25.94 30.00 31.58 31.50 1.02 1.56 .75 .61  ¾x5 16 30 32.00 4.00 33.29 33.46 32.17 36.88 39.12 39.12 1.31 2.00 .82 .66 1¿ 1x6 20 36 38.30 4.00 39.59 39.76 38.47 43.75 46.00 46.00 1.45 2.00 1.00 .74 1¿ 1x6 24 42 44.50 4.00 45.79 45.96 44.67 50.62 53.12 53.12 1.45 2.00 1.25 .82 1À 1¼x6½ 28 48 50.80 4.00 52.09 52.26 50.97 57.50 60.00 60.00 1.45 2.00 1.35 .90 1À 1¼x6½ 32 11910 CR 492-Tyler, TX 75706-(800) 527-8478 .-L 1- 1001 ElCamino Ave.-Corona, CA 92879-(866) 527-8471 6204 N. M www.tylerunion.com 28U - Flange Joint AWWA C110/A21.10 Full Body Revised 0 6/1 1 SUBMITTAL (Current r evisions for a ll Standards a pply) SIZES: ............................2” through 48” STANDARDS: .................ANSI/AWWA C110/A21.10-08 plus NFPA 3" to 12" UL listed (EX 2111) Note: Cast with tested and traceable ASTM A536 Ductile Iron PRESSURE RATING: .......2”-48” rated @ 250 psi Note: With the use of special flange gasket 2”-24” flanged fittings c @ 350 psi. For 350 psi flange joint applications, we recommend t annular ring type gasket or comparable. DEFLECTION: .................Deflection is not recommended for flanged joint upon completion of installation. NSF-61: .........................Meets all requirements, UL Listed (MH16439) COATING: ......................ANSI/AWWA C104.A21.4-08 (Asphaltic or Tnemec Pota Pox 140N-1211) CEMENT LINING: ..........ANSI/AWWA C104.A21.4-08 (Double Cement lined Available) EPOXY COATING:..........ANSI/AWWA C116/A21.16-09 Note: Epoxy coated fittings are available to the specification(s) req application(s) BARE: .............................Available FLANGES: ......................ANSI Class 125 per ASME B16.1 and ANSI/AWWA C111/A21.11-7 Note: *ANSI Class 250 ASME B16.1 flanged fittings available Note: *Due to larger bolt sizing and bolt circle, C lass 250 flanges are not compatible with Class 125 flanged fittings. AWWA C110 and AWWA C115 Class 125 flanges are compatible. FLANGE THICKNESS: ....ANSI/AWWA C151/A21.51-05; Standard Class 125 template for drilli Note: Drilling templates are in multiplies of 4, so that fittings may any quarter. Bolt holes shall straddle the center line. BOLTS: ...........................ANSI/AWWA C111/A21.11-7 INSTALLATION: .............Per AWWA C600-10 using pipe conforming to ANSI/AWWA C151/A21.51-02 FLANGE DETAILS Nominal Dia. of Flange Pipe Size Flange Bolt Thickness Bolt Hole Number Bolt Dia. Inch O.D. Circle T Diameter of Holes & Lengths 2 6 4.75 .62 .75 4 Áx2¼ 3 7.5 6 .75 .75 4 Áx2½ 4 9 7.5 .94 .75 8 Áx3 6 11 9.5 1.00 .875 8 ¾x3½ 8 13.5 11.75 1.12 .875 8 ¾x3½ 10 16 14.25 1.19 1.00 12 Âx4 12 19 17 1.25 1.00 12 Âx4 14 21 18.75 1.38 1.125 12 1x4½ 16 23.5 21.25 1.44 1.125 16 1x4½ 18 25 22.75 1.56 1.25 16 1¿x5 20 27.5 25 1.69 1.25 20 1¿x5 24 32 29.5 1.88 1.375 20 1¼x5½ 30 38.75 36 2.12 1.375 28 1¼x6½ 36 46 42.75 2.38 1.675 32 1½x7 42 53 49.50 2.62 1.625 36 1½x7½ 48 59.50 56.00 2.75 1.625 44 1½x8 Tyler Union W 11910 CR 492 - Tyler, TX 75706 - (800) 527-8478 . -L 1 - 1 1001 ElCamino Ave. - Corona, CA 92879 - (866) 527-8471 6204 N ® ® 9.8 MUELLER SUPER CENTURION FIRE HYDRANT Rev. 8-04 Shaded area indicates changes ™ Super Centurion 2503-way catalog numbers (approved to UL 246, FM 1510, ANSI/AWWA C502 Standards) - A-421 4-1/2" main valve opening three way (two hose nozzles and one pu A-423 5-1/4" main valve opening three way (two hose nozzles and one pu ™ Super Centurion 2002-way catalog numbers (approved to ANSI/AWWA C502 Standards) - A-420 4-1/2" main valve opening two way (two hose nozzles) A-422 5-1/4" main valve opening two way (two hose nozzles) A-425 5-1/4" main valve opening two way (two pumper nozzles) ™ Super Centurion 2001-way catalog number (approved to ANSI/AWWA C502 Standards)- A-424 4-1/2" main valve opening one way (one pumper nozzle) 10 year limited warranty on material and workmanship Meets all applicable parts of ANSI/AWWA C502 Standard Post type dry barrel design Dry top design with O-ring sealed oil reservoir Compression-type main valve closes with pressure for positive se and is conveniently reversible providing a spare for long servic Operating nut available in wide variety of shapes and sizes-open Field replaceable hose and pumper nozzles Dual bronze drain valves provide effective barrel drainage 250 psig (1723 kPa) maximum working pressure, 500 psig (3447 kPa 200 psig (1379 kPa) maximum working pressure, 400 psig (2758 kPa Dimensions Non-rotating bolt design: cast-in pads elimi- nate need for anti-rotation bolts. Mechanical joint standard and D-150 Front view detail of Mechanical joint (Standard only) Flange ANSI 125/150 or PN 10/16 Drilling Vertical Flange* Slip-on * 4" Vertical shoe available for A-420 and A-421 hydrants. SEE PAGE 9.28 FOR ORDERING INSTRUCTIONS SUBMITTAL INFORMATION Ballcorp Corporation Stops - (FB700-7-NL style) MALE IRON PIPE THREAD INLET BY FLARE COPPER OUTLET Solid one piece tee-head and stem Molded EPDM rubber seat supports the ball EPDM O-rings in the stem Flare Copper Nut MIP Threads InletOutlet Fluorocarbon-coated brass ball Length VB OA.P S ALVEODYUTLETPPROXART UBMITTED V SI SO S ALVEIZENLETIZEUTLETIZE LTW. LN I() ENGTHHREADSTBSUMBER TEMS 2" 2"2" 7-47/64"2" Flare Copper9.7FB700-7-NL FEATURES • All brass that comes in contact with potable water conforms to AWWA Standard C800 (UNS NO C89833) • The product has the letters "NL" cast into the main body for proper identification • UL Classified to ANSI/NSF Standard 61 and Standard 61 Annex G (NSF/ANSI 372) • Brass components that do not come in contact with potable water conform to AWWA Standard C800 (ASTM B-62 and ASTM B-584, UNS NO C83600 - 85-5-5-5) • Ends are integral or secured with adhesive to prevent unintentional disassembly • 300 PSI working pressure The Ford Meter Box Company considers the information in this submittal form to be correct at the time of publication. Item and option availability, including specifications, are subject to change without notice. Please verify that your product information is current. Submitted By: The Ford Meter Box Company, Inc. P.O. Box 443, Wabash, Indiana U.S.A. 46992-0443 Phone: 260-563-3171 / Fax: 800-826-3487 Overseas Fax: 260-563-0167 http://www.fordmeterbox.com 01/30/13 UBW,I. NITED RASS ORKS NC 714 S. Main St., Randleman, NC 27317 www.ubw.com Tel: 800-334-3035 Fax: 800-498-4696 Model 90 Wafer Check Valve UL Listed * As antiwater hammer check valve for fire pump service only! 250 WOG @ 180° Max 100% Pressure Tested Approved by New York City Board of Standards & Appeals under Calendar No. 157-84-SA. in drain port as standard configuration. *Contains Lead. Not Intended for Use in Potable Water Systems* MATERIAL LIST NO. DESCRIPTION MATERIAL 1 Body Ductile Iron 2 Seat Ring Assembly Bronze 3 Screw Stainless Steel 4 Seat Ring O-Ring Buna-N 5 Face O-Ring Buna-N 6 Pipe Plug Steel Ship Wt. Qty. Per Size A B C D (lbs) Ctn. 4.25 4.03 6.86 3.00 15.0 1 3.75 6.06 8.50 4.50 19.0 1 3.75 7.98 11.00 6.00 29.0 1 CIC, ASTRONOMPANION R, & BF EDUCINGLINDLANGES ABBGASTM 126 CB CI VAILABLEINOTHLACKANDALVANIZEDLASSASTRON ANSI C125 F LASSLANGES APPLICATIONS: W, P& W, P, I ATERWORKSUMPELLLUMBINGRRIGATION CH ORPORATEEADQUARTERS M-N, I. ATCOORCANC B, NY REWSTEREWORK P. O. B27 R22 B, NY10509 OXOUTEREWSTER T: 845-278-7570 F: 845-278-9056 ELAX TF: 800-431-2082 F: 800-640-2252 OLLREEAX Visit our web site: www.matco-norca.com email: mail@matco-norca.com WRCR ESTERNEGIONENTRALEGION M-N, I. M-N, I. ATCOORCANCATCOORCANC LP, CH, T AALMAALIFORNIAOUSTONEXAS 1150 SRH, TX 77055 5593 FDLP, CA90623 ILBEROADOUSTON RESCARIVEAALMA T: 713-680-2888 F: 713-680-2999 T: 714-522-1889 F: 714-522-3828 ELAX ELAX TF: 800-935-5456 F: 800-683-4247 OLLREEAX TF: 866-532-8306 F: 866-532-8307 OLLREEAX CIC, ASTRONOMPANION R, & BF EDUCINGLINDLANGES ABBGASTM 126 CB CI VAILABLEINOTHLACKANDALVANIZEDLASSASTRON ANSI C125 F LASSLANGES APPLICATIONS: W, P& W, P, I ATERWORKSUMPELLLUMBINGRRIGATION COMPANION CFD OMPANIONLANGEIMENSIONS 6 x 11 ø SIZESIZE x ODABCDEMN 6 1-1/2Ž1-1/2 x 55.003.880.880.562.561.890.634 2Ž2 x 66.004.751.000.623.062.360.754 2-1/2Ž2-1/2 x 77.005.501.120.693.562.870.754 3Ž3 x 7-1/27.506.001.190.754.253.390.754 3-1/2Ž3-1/2 x 8-1/28.507.001.250.814.813.860.758 4Ž4 x 99.007.501.310.945.314.410.758 5Ž5 x 1010.008.501.440.946.445.430.898 6Ž6 x 1111.009.501.561.007.566.420.898 8Ž8 x 13-1/213.5011.751.751.129.698.430.898 M-N 10Ž10 x 1616.0014.251.941.1911.9410.431.0012 12Ž12 x 1919.0017.002.191.2514.0612.401.0012 REDUCING C D RFD EDUCINGLANGEIMENSIONS ø SIZESIZE x ODABCDEMN 4Ž x 2Ž2 x 99.007.501.000.943.062.360.758 4Ž x 3Ž3 x 99.007.501.190.944.253.390.758 5Ž x 4Ž4 x 1010.008.501.310.945.314.410.898 6Ž x 2Ž2 x 1111.009.501.061.003.062.360.898 6Ž x 4Ž4 x 1111.009.501.311.005.314.410.898 6Ž x 5Ž5 x 1111.009.501.441.006.445.430.898 8Ž x 2Ž2 x 13-1/213.5011.751.191.123.062.360.898 8Ž x 3Ž3 x 13-1/213.5011.751.191.124.253.390.898 8Ž x 4Ž4 x 13-1/213.5011.751.311.125.314.410.898 8Ž x 5Ž5 x 13-1/213.5011.751.441.126.445.430.898 8Ž x 6Ž6 x 13-1/213.5011.751.561.127.566.420.898 BLIND 4 BFD LINDLANGEIMENSIONS SIZEABCDMN 2Ž6.004.752.000.620.754 2-1/2Ž7.005.502.500.690.754 3Ž7.506.003.000.750.754 4Ž9.007.504.000.940.758 5Ž10.008.505.000.940.898 6Ž11.009.506.001.000.898 8Ž13.5011.758.001.120.898 10Ž16.0014.2510.001.191.0012 M-N 12Ž19.0017.0012.001.251.0012 D H, TX B, NY OUSTON REWSTER T:800-935-5456 F:800-683-4247 T:800-431-2082 F:800-640-2252 ELAX ELAX LP, CA AALMA V: www.matco-norca.com ISITOURWEBSITE T:866-532-8306 F:866-532-8307 ELAX