Coppell Trade 3-CS161208
EVERGRIP 990-STRIPS
EVERGRIP 990-STRIPS
POLYMER MODIFIED CONCRETE JOINT SEALANT
Evergrip 990 is a concrete joint sealant made with a unique blend of
asphalts enriched with high grade polymer.Available in convenient
strips,Evergrip 990 is a preformed,ready-to-use,flexible gasket that
provides an excellent seal for concrete pipes,culverts,manholes and
other precast concrete joints.
ADVANTAGES
A polymer modified sealant,Evergrip 990 offers significant
advantages over non-modified sealants:
¥ 60% more adhesive strength
¥ 366% more cohesive strength
¥ Greater elasticity
¥ 40% higher ductility
¥ Consistent performance over a wider range of temperatures
¥ Provides watertight seal
¥ For concrete joints of all sizes and shapes
¥ Extruded strips for easy application
¥ Available in standard sizes and lengths
¥ Asbestos free
¥ Odorless
¥ 100% solids
¥ No primer necessary
¥ No shrinkage
MEETS STATE AND FEDERAL REQUIREMENTS
EVERGRIP 990 STRIPS
POLYMER MODIFIED CONCRETEJOINT SEALANT
Evergrip 990 meets or exceeds all requirements of ASTM C 990,
U.S.Federal Specifications SS-S-210A,Type 1,Rope Form and
AASHTO Designation M-198 75 I,Type B.Certified to meet or
exceed highway department specifications.
EVERGRIP 990 APPLICATION
SURFACE PREPARATION
Concrete surfaces to which sealant is to be applied must be clean
and dry.Remove all mud,dirt,grease,oil and loose particles.
APPLICATION
Remove release paper from one side of sealant.Leave the outside
paper in place to protect the sealant from contamination and
stretching.Attach the sealant end to end to the leading edge of the
A B A B
tongue or groove of each pipe joint until a continuous gasket is
established around the entire circumference of the pipe joint.Press
material firmly into place through the outside paper.Remove the
outside paper just prior to jointing the pipe.Avoid contaminating
the exposed sealant with any foreign materials.Any contaminated
sealant should be removed and replaced.Do not disturb the gasket
A) Sealant Placement
B) Joint After Compression
EVERGRIP 990-STRIPS
EVERGRIP 990-STRIPS
POLYMER MODIFIED CONCRETE JOINT SEALANT
placement.Any displaced sealant should be repositioned prior to
jointing the pipes.
PACKAGING(ENGLISHSTANDARD)
Read pipe manufacturer's instructions for proper pipe jointing proce-
dures.The trench can be backfilled as soon as the joining process has
SEALANTSIZEPIECES/CARTONFT./CARTON
been completed.
3/4" x 2'6"50125 ft
WORKING CONDITIONS
1" x 2'6"3587.5 ft
Conditions must preclude contamination of the sealant during the
1" x 3'6"35122.5 ft
installation process by any foreign material such as silt or mud.
1 1/4" x 3'6"2898 ft
1 1/2" x 3'6"2070 ft
1 3/4" x 3'6"1345.5 ft
STORAGE
2" x 3'6"1035 ft
Store in a dry area protected from the elements.Do not stack car-
tons over six high.
PACKAGING (METRIC)
PIECES/
SEALANTSIZEM/CARTON
CLEAN-UP
CARTON
Scrape excess sealant off surfaces.Asphalt stains can be removed
19mm x 762mm5038.1 m
with non-hazardous,bio-degradable cleaners.Use waterless hand
25.4mm x 762mm3526.7m
cleaner on skin.Follow cleaner manufacturerÈs instructions carefully.
25.4mm x 1067mm3537.3m
Do not use flammable or combustible petroleum based solvents.
31.75mm x 1067mm2829.9m
38.1mm x 1067mm2021.3m
44.45mm x 1067mm1313.9m
50.8mm x 1067mm1010.7m
PROPERTIES AND PERFORMANCE DATA
Bitumen,% by wt.50-70
Inert filler content,% by wt.30-50
Volatile matter,max.% by wt.2.0
PROPERTIES
oo
Specific gravity @ 77F/25C,(gr/ml)1.2-1.35
oo
Ductility @ 77F/25C,(cm),min.5.0
oo
Min.softening point320F/160C
oo
Min.flash point,C.O.C.600F/315C
oo
Penetration @ 77F/25C,150 gms,5 sec.(dmm)50-120
Adhesion and hydrostatic pressureNo leaks (24 hrs.)
Sag or flow resistanceNo sagging
Chemical resistanceNo visible deterioration
Read and understand MSDS sheet before use.