Westhaven Phase 2B-150825LMC
Date: 08/25/2015
Client: TEXAS INLETS INC
Attention:
Project: WESTHAVEN PHASE 2B
Location: COPPELL, TEXAS
Lattimore Materials Corp.
15900 DOOLEY ROAD
ADDISON TX 75001
(972) 221-4646 (main)
(972) 221-9647 (fax)
Usage
Mix Number
f 'c
wlc+p
Slump
Air
INLETS, MANHOLES,
HEADWALLS
1701.
4000
0.45
3.00 - 5.00"
3.0-6.0%
LMC has no knowledge or authority regarding where this mixture is to be placed, therefore it is the direct responsibility of the
Purchaser, the design architect or design engineer, and or contractor to insure that the above designed mixture parameters for
compressive strength, mixture proportions or ratios, and other required performance parameters are appropriate for the
anticipated environmental, durability, or usage conditions in ACI 318 Chapter 4 and/or the relevant local building codes.
LMC warrants the supplied ready -mix concrete mixture designs which LMC guarantees will achieve the specified compressive
strength, or other performance properties of the concrete stated in the Contract Documents, as were made available at the time
of quotation, when tested and evaluated in accordance with ASTM C172-99, ASTM C31/C31 M -03a (including proper initial
curing as per Section 10.1.2), ASTM C39/C39M-01, ASTM C94/C94M-07, or other standard test methods indicated in the
Contract Documents that were necessary to verify the additional performance properties of the concrete, and when the
recommended procedures for placement and curing of the in-place concrete, or those specifically outlined in ACI 305R-99 and
ACI 306R-88 are followed, if and when necessary.
In accordance with ASTM C94/C94M-07 Section 4.6, Lattimore Materials Corp shall receive all copies of testing reports, and
they should be forwarded to our Quality Control Department (mixdesign@aggregate-us.com) as soon as available. Failure to
forward reports in a timely fashion can delay response time in dealing with concrete concerns as well as future project
submittals.
This mix design submittal, price quote, or material specific information (aggregate properties, grading, material composition, or
other information regarding materials manufactured by Lattimore Materials Corp) is proprietary and confidential and not to be
shared or transmitted in any form to any person or organization that is not expressly authorized in writing by a designated official
of Lattimore Materials Corp. Any unauthorized person or entity in possession of this information will be prosecuted to the fullest
extent of the law.
Material certifications for concrete constituents are representative of current material sources. If, in the event of limited material
availability, substitution of a similar performing material may be required. Such materials will meet the appropriate ASTM
requirements as stated in this package. In order to maintain the required mix volume (yield), LMC reserves the right to adjust
absolute weight of aggregates to accommodate specific gravity changes.
LMC mix designs requiring air -entrainment are produced in accordance wiht ASTM C 94 Section 8.2, which allows for a
tolerance of 1.5% above and below the target, and is stated as follows: ASTM C94IC94M -13a 8.2 The air content of
air -entrained concrete when sampled from the transportation unit at the point of discharge shall be within a tolerance of +/-1.5 of
the specified value.
1992 - 2015 Digital Site Systems, Inc. page 1 Quadrel iService
SM
LMC
Date:
Client:
Project:
Concrete Mix Design
08/25/2015
TEXAS INLETS INC
WESTHAVEN PHASE 2B
COPPELL, TEXAS
1.0 Cubic Yard by Weight - SSD
Mix Number: 1701.
Strength @ 28 Days: 4000 psi
Usage: INLETS, MANHOLES, HEADWALLS
Lattimore Materials Corp.
15900 DOOLEY ROAD
ADDISON TY. 75001
(972) 221-4646 (main)
(972) 221-9647 (fax)
Materials:
4001 Ibs
Unit Weight:
SSD Weights
Cement
ASTM C-150
Type 1/11
564 lbs
Coarse Aggregate
ASTM C-33
1"-#4 Crushed Stone
1850 lbs
Fine Aggregate
ASTM C-33
Concrete Sand
1328 lbs
Water
ASTM C-94
Water
256 lbs
Admixture
ASTM C-260
Air -Entraining Admix
0.65 oz/cwt C+P
Admixture
ASTM C-494
Type A/D WR
4.0 oz/cwt C+P
Admixture
ASTM C-494
Type B/D WR
1.0 oz/cwt C+P
Total Weight:
4001 Ibs
Unit Weight:
148.09 pcf
w/cm Ratio:
0.45
Fly Ash Replacement:
0.0%
Slump:
3.00 - 5.00 inches
Air Content:
3.0-6.0%
Comments:
The cementitious content of the mix design is stated as a minimum and Lattimore Materials Corp. reserves the right to
increase cementitious content if needed.
Chemical admixtures are added in accordance with the manufacturer's recommendations. Lattimore Materials Corp.
reserves the right to adjust dosages or change admixtures when required.
1992 - 2015 Digital Site Systems, Inc. Page 3 Quadrel Service sm
LMC
Data: 8/25/2015
Mix Name: 1701. Statistical Compressive Strength History units: US
PSI Strength and Strength Fit vs Maturity PSI # of Occ. Histogram for 28 Day Strength %/PSI
8500
8000
7500
7000
6500
6000
5500
5000
4500
4000
3500
r
0 10 20 30 40 50 60
8500
8000
7500
7000
6500
6000
5500
5000
4500
4000
3500
14.000.09
12.00
Date
Slump Spread
d
Strengths
Acc Age
10.00
8.00'
6.00
4.00
2.00
0.00
I
�
i
I
0.08
0.06
0.05
0.04
0.03
0.01
0.00
�
62964584
5/16/2014
4.25
5.10
l
6110
64363543
4500 5000 5500 6000 6500 7000 7500 8000 8500
Maturity Days PSI
95016 of tests lie above cross -hatched area
STRENGTH SUMMARY, Compression Either 4" x 8" Or 6" x 12"
Strengths
No. Of Avg Avg Avg 3 Avg 7 Avg 28 Std ACI318
Tests Slump Air Day Day Day Dev Req'd
------------------------------------------------------------------------------
30 3.53 3.61 4930 6250 440 4600
DETAILED STRENGTH, Compression Either 4" x 8" Or 6" x 12"
Batch
Date
Slump Spread
Air
Strengths
Acc Age
Number
------------------------------------------------------------------------------
3 Day 7 Day
28 Day
Run Avg 3
62964584
5/16/2014
4.25
5.10
5070
6110
64363543
5/22/2014
5.00
4.30
4190
6040
63688481
6/2/2014
2.50
2.00
4540
5860
6000
63690516
7/15/2014
3.50
5.30
5200
5900
5930
71001005
7/22/2014
2.50
3.30
5310
6330
6030
62492090
8/1/2014
3.50
4.80
4920
6620
6280
62815637
8/18/2014
3.75
4.50
5050
6230
6390
63692401
8/19/2014
1.00
3.00
5110
5990
6280
71004393
10/3/2014
2.75
4.10
4990
6130
6110
62499124
11/12/2014
4.00
3.30
4320
5980
6030
71005756
11/12/2014
3.75
4.50
5270
6330
6150
63164624
11/17/2014
4.00
3.90
4860
5970
6100
63696592
11/17/2014
4.50
4.20
4880
6310
6200
71006609
12/3/2014
8.00
2.00
3720
5810
6030
62502067
1/14/2015
5.00
2.30
4590
6520
6210
63698897
1/14/2015
1.25
3.00
4980
6150
6160
63699957
1/30/2015
1.50
2.20
4960
6170
6280
62821839
2/4/2015
3.50
4.60
5280
6630
6310
63700189
2/4/2015
2.00
2.60
5610
6890
6560
62821933
2/5/2015
3.00
3.40
5580
8130
7210
1992 - 2015 Digital Site Systems, Inc. page 4 Quadrel iService
SM
DETAILED STRENGTH, Compression
Batch Date Slump Spread Air
Number
63089104
2/10/2015
4.00
63170099
2/12/2015
3.75
63089504
3/12/2015
4.00
63172188
4/3/2015
3.50
63172530
4/8/2015
3.00
63173005
4/15/2015
6.25
62824469
4/30/2015
3.00
63289642
5/28/2015
2.25
63704093
6/16/2015
3.00
62826576
6/30/2015
4.00
2.60
4.20
3.70
3.90
4.20
3.00
3.00
3.50
4.30
Either 4" x 8" Or 6" x 12"
Strengths
Acc Age
3 Day 7 Day
----------------------------------
28 Day
Run Avg 3
5450
6020
7010
4230
6350
6840
5170
6480
6290
4960
6100
6310
5070
6000
6190
3880
5940
6010
5160
6080
6000
4950
5810
5940
5600
6800
6230
4930
5990
6200
1992 - 2015 Digital Site Systems, Inc. Page'S Quadrel iService
SM
I
Holcim
Material:
Type:
vCrslon
Material Certification Report
Portland Cement Test Period: 01 -Mar -2015
1-11 To: 30 -Mar -2015
= Cefic*jai� .
This Holcim cement meets the specifications of ASTM C150 for Type WI cement
General Infomiatian
1, '
Supplier:nUInc. Source Location: on: Midlothian Plant
Address: 1800 ( Lane- -
1800 Dove Lane
Midlothian, TX, 76065 Midlothian, TX, 76065
Telephone: (972) 923-5800 Contact: Javier Sosa
Date Issued: 13 -Apr -2015
The foilov ing information is based on average test data during the test period.
The data is
typical of cement shipped by Holcimindividual shipments may vary.
Tests'D to orl`AST11ll tarsi iald I egillremen s ,
Chemical Physical
Item Limit"' Result Item Limle Result
I % 19.7 Air Content (%) 12 max 9
A603 (%) 6.0 max 4.7 Braine Fineness (m2/kg) 260 min 377
F6203 (°h) 6.0 max 3.3
coo (%) - 642
M90 (°Yo) 6.0 max 0.9 Autoclave Expansion (%) (C151) 0.80 max 0.06
S03 (%) 3.0 maxa 3.5 Compressive Strength MPa (psi):
Loss on Ignition. (%) 3.0 max 2.3
Insoluble Residue (%} 0.75 max 0.49 3 days 12.0 (1740) min 27.6 (4000)
CO2 (%)° - 1.1 7 days 19.0 (2760) min 33.8 (4900)
Limestone (/o) 5.0 max 3.2
CaCO3 In Limestone (%) 70 min 79 Initial Vicat (minutes) 45-375 104
Inorganic Processing Addition 5.0 max 0.0
Potential Phase Compositlone: Mortar Bar Expansion (01038) - 0.010
C3S (%) - 63
CzS (%) - 8
C3A (%) 8 max 7
CAF (%) - 10
C3S + 4.75C3A 96.3
LL ` bests Data a AS M'= ho at Regairemlenfs
n Tr � rr: r
Chemical Physical
Item Limit" Result° Item Limle Result
Equivalent Alkalies (%) - 0.60
—^.-�I,��1�.f ,y Y.h� i i1� .,}`r d,��uS ya' , '�I L r d � l..' t 4 - L.n� i ,ti•= -, � t.
" Dashes in the limit / result columns mean Not Applicable.
ift
° It is permissible to exceed the specification limit provided that ASTM C1038 Mortar Bar Expansion does not exceed 0.020 % at 14 days.
c Ad)usled per Annex A1.6 of ASTM C150 and AASHTO M85. ti
° Maximum total alkali, based on a 95% confidence interval level per TxDOT DMS 4600.
This data may have been reported an previous mill certificates.
sale of Tome countyot f 0 Q�,�,(�) � LINDA K. LANIER
t1Nom end a bed before 1119 tlYs ]� J' St PublicNotioy
°� - �pJ-`�� a eXas
Comm, E>�ires 2-20-2017
Pebld
A(iCWlotlal Data t i i,
Inorganic Processing Addition Data Base Cement Phase Composition w
Item Resuir Item Result
Type - Cas NO 65
Amount (%) _ (yo)
Sit (%) _ 9
AIz03 (°A) _ CaA (%) 7
C4AF (%) 10
Fe203 (%) _
CaO (%) _
S03(%) _
By �. — , Quality Manager
Javier Sosa
man
saw
HMDEL.BEROCEMENTGtoup
Hanson Aggregates
Southwest Region
Technical Services Lab
1000 N. MacArthur Blvd.
Grand Prairie, TX 75050
Tel. 972-260-3646
Fax. 972-260-3655
www.hansonpic.com
MATERIALS EVALUATION
Coarse Aggregates
Source: Hanson L? Bridgeport (Perch -Hill) Plant Technical Services
#777
Type: ASTM #57 (1" - #4) Crushed Lime Stone Report: 2015-777
Lab NO: TS -Weekly -15 Date: 07-24-15
Date: Received: 07-01-I5
ASTM
METHOD
TEST
DESCRIPTION
TEST
RESULTS
ASTM C-33
Specification
C-136
2''
Sieve
100
% Passing
--------
C-136
1-l%2"
Sieve
I00
°,o Passin_
100
C-136
1"
Sieve
96
% Passing
95-100
C-136
;i4"
Sieve
78
% Passing
-------
C-136
UT'
Sieve
49
% Passing
25-60
C-136
3J8"
Sieve
36
% Passing
-------
C-136
#4
Sieve
6
4o Passing
0-10
C-136
48
Sieve
2
°io Passing
0-5
C-136
#16
Sieve
2
% Passing
-------
C-117 Decant (- #200 Sieve Washed)
C-127
Relative Bulk Specific Gravity., SSD
C-127
Relative Bulk Specific Gravity. Dry
C-127
Absorption,
C-29
Unit Weight (Dry Rodded),
C-29
Unit Weight (Dry Loose),
C-29
Voids Content (Dry Rodded),
C-131
L.A. Abrasion.
C-1260
Potential Alkali Reactivity of Aggregates,
C-88
Soundness by Sodium
26.8
Sulfate (5 cycles). ....... I......
C-88
Soundness by Magnesium
Ob Exp.
Sulfate (5 cycles), ...............
C-123
Light Weight Pieces.
C-142
Clay Lumps and Friable Particles,
C-25
Calcium Carbonate EQV.
C-25
.Acid Insoluble Residue.
Note: - Hanson Product Code TX -130
0.90 % Passing 1.5% Max.
2.663
2.632
0.9
%
104.4
Lbs/Cu.Ft.
94.1
Lbs.!Cu.Ft.
38.3
26.8
°10 Loss
50% Max.
0.03
Ob Exp.
0.1 % Max
2.30
°'o Loss
12% Max.
3.90
% Loss
18% Max.
0.01
°0
0.5% Max.
0.01
° 1
3.0% Max.
9,614�0
.0
4
.0 'G
c
A
itSr1 r�i 1�'�+t�R Y
Varian Babakhanian. P.E. � � d fi d
Technical Services Lab Manager
Our letters, anahsis and reports are for the exclusive use of the client to whom the} are addressed. appl} oniv to the sample tested and or inspected and are not necessarily
indicative of the qualities of apparentic identical or similar products. This report shall not be reproduced except in hall and with the written approtial of HANSOM PLC.
LMC
yrs" -rq '.,`77"�,_
Gradation Ana
ASTM C29, i
Date Sampled: 22 -Jun -2015
Date ran: 24 -Jun -2015
Total dry wt: 708.4 grams
Lattimore Materials Corp.
15900 Dooley Road
Addison, Texas 75001
972-221-4646 (main)
972-221-9647 (fax)
www.laftimorematerials.com
C117, C128 & D75
Sample: Blend Spec Sand
Source: Ambrose
Location: Loadout @a Radial
Sieve
Size (in)
Wt. Ret.
%o Ret.
% Pass
% Passing ASTM
% Retained TxDOT
C33 Limits
421
3/8"
0.375
0.0
0.0%
100.000
100%
0%
#4
0.188
13.7
1.9%
98.1%
--95-0/0- 1-
00%
0%-5%
#8
0.094
129.3
18.3%
81.7%
80%-100%
#16
0.047
204.6
28.9%
71.1%
50%-85%
—0%-20%
15%-50%
#30
0.023
281.9
39.8%
60.2%
25%,-60%
35% - 75%
#50
0.012
566.4
80.0%
20.0%
5%-30%
65%-90%
#100
0.006
667.2
94.2%
5.8% 1
0%-100
90%-100%
#200 1
0.003
705.1
99.5%
0.5%
0% - 3%
97%-100%
PAN
S.E.. 97
Fineness Mod.: 2.63
Specific Gravity: 2.61
Dry Loose Unit Wt: 93.62 ib/ft3
Dry Rodded Unit Wt: 111.06 Ib/ft3
Absorbtion: 1.03%
+o: •� BRANDI ANN HOWELL
Notary public, Siate of Texas
MY Commission Expires
'��"�.•� Februar7
Y 5, 2016
X2
1
Product Data Sheet
Edition 09.25.2009
Identification no. 147-540
Sika Air
Sika° Air
Air Entraining Admixture
Description Sika Air admixture is an aqueous solution of organic materials.
Sika Air meets the requirements of ASTM C-260 for air entraining admixtures.
Applications
Advantages
How to Use
Sika Air is recommended for use whenever air entrained concrete is desired.
Ready -mix, precast and block producers can achieve predictable and uniform
entrained air contents in concrete, even where harsh lean mixes are used or
fly -ash is added to the concrete.
Durability:
■ Air entrainment is recognized as the most effective prevention against con-
crete scaling in exposed environments. Air entrained concrete delivers par-
ticular benefits in the form of increased concrete durability. This is important
in colder climates where frost and freeze -thaw cycles can cause scaling and
damage to the concrete surface.
■ Air entraining agents help to prevent scaling by creating microscopic air
voids that water trapped in the concrete can expand into when the concrete
freezes, thus preventing cracks caused by the natural expansion. Entrained
air voids in the concrete will also increase durability in harsh environments
where concrete is exposed to deicing salts, marine salts and sulfates.
Workability and Placeability:
■ Workability and placeability are also improved by the lubricating action of the
microscopic bubbles in the concrete. Concrete will flow better, and bleeding
and shrinkage will be reduced because less water is needed to obtain the
desired workability.
Dosage rates for Sika Air will typically fall between 0.5 and 3 fl. oz. per 100
lbs. (32 -195 ml/100 kg) of cementitious to entrain between 4 and 6 percent
air. Higher air contents may be obtained by increasing the dosage rate.
Dosage rates will vary depending on the air content required for a particular
project. Typically air contents will be specified in the range of 4 to 8 percent by
volume.
Other factors that may affect the amount of air entrained into the concrete
including total cementitious content, type of pozzolanic materials, sand grada-
tion, salt/clay in aggregates, temperature and water content. The use of fly
ash, particularly high LOI fly ash, can result in a higher dosage of air entrain-
ment. Sika recommends that trial mixes be performed whenever material or
any other changes are made that may affect the amount of entrained air.
In mixes requiring a lower or higher amount dosage rate, please contact your
local regional Sika office or Sika technical service department at 1-800-933-
7452 for further information.
=; Mixing
Measure the required quantity per batch manually or with automatic dispenser
me ,
equipment. Add Sika Air to mixing water or sand. Do not mix with dry cement.
When Sika Air is used in combination with other admixtures, care must be
k,
atm
taken to dispense each admixture separately into the mix.
ti =s�
Combination
c
with Other Admixtures:
h
«h5=
Combination with other admixtures, particularly water reducers and retarders, may
increase the amount of entrained air in the mix. Air contents should be checked with
an air -meter after batchingand dosage adjustments made at the concrete plant.
9 1
C Packaging
Sika Air is available in 55 gallon drum (208 liter), 275 gallon totes (1040 liters)
Y�
drums and bulk delive
Storage and Shelf life
Sika Air should be stored at above 40°F (50C). If frozen, thaw and agitate
thoroughly to return to normal state.
Shelf life when stored in dry warehouse conditions between 50°F and 80°F
R
x ,
(10°C - 27°C) is one year.
Typical Data
Appearance
Dark Amber liquid.
Specific Gravity
Approx. 1.0
CAUTION: IRRITANT
Contains Aqueous Solution (CAS:Mixture). May cause eye/skin/respiratory
a y{
irritaton. May be harmful if swallowed.
Handling and Storage
Avoid direct Wear
contact. personal protective equipment (chemical resistant
goggles/gloves/clothing) to prevent direct contact with skin and eyes. Use
only in well ventilated areas. Wash thoroughly with soap and water after use.
1
Remove contaminated clothing and launder before reuse.
! First Aid
Eyes: Hold eyelids apart and flush thoroughly with water for 15 minutes. Skin:
Remove contaminated clothing. Wash skin thoroughly for 15 minutes with
soap and water. Inhalation: Remove person to fresh air. Ingestion: Do not
'< V
induce vomiting. Dilute with water. Contact physician. In all cases contact a
physician immediately if symptoms persist.
' +i
Safety
Tested and Certified by WQA according to NSF/ANSI 61 Section 5 for
s'k
materials safety.
}
Clean Up
t
Use personal protective equipment (chemical resistant goggles/gloves/cloth-
ing). Without direct contact, remove spilled or excess and in
product place
suitable sealed container. Dispose of excess product and container in accor-
dance with applicable environmental regulations.
KEEP CONTAINER TIGHTLY CLOSED • KEEP OUT OF REACH OF CHILDREN • NOT FOR INTERNAL CONSUMPTION • FOR INDUSTRIAL USE ONLY
Al information provided by Sika Corporation CSika°) concerning Sika products, including but not limited to, any recommendations and advice
relating to the application and use of Sika products, is given in good faith based on Sike's current experience and knowledge of its products
when property stored, handled and applied under normal conditions in accordance with Sike's instructions. In practice, the differences in materi-
als, substrates, storage and handling conditions, actual site conditions and other factors outside of Sike's control are such that Slice assumes no
liability for the provision of such information, advice, recommendations or instructions related to Its products, nor shall any legal relationship be
created by or arise from the provision of such information, advice, recommendations or instructions related to its products. The user of the Sika
product(s) must test the product(s) for suitability forthe intended application and purpose before proceeding with the full application of the product(s).
Sika reserves the right to change the properties of its products without notice. All sales of Sika product(s)
are subject to its current terms and conditions of sale which are available at www.sikacorp.com or by calling 800-933-7452.
Prior to each use of any Sika product, the user must always read and follow the warnings and instructions on the product's most cur-
rent Technical Data Sheet, product label and Material Safety Data Sheet which are available at www.sikaconstruction com or
800.933-7452. Nothing contained in any Sika materials relieves the user of the obligation to read and follow the warnings and instruction
for each Sika product as set forth in the current Technical Data Sheet, product label and Material Safety Data Sheet prior to product use.
SIKA warrants this product for one year from date of installation to be free from manufacturing defects and to meet the technical properties
on the current Technical Data Sheet if used as directed within shelf fife. User determines suitability of product for intended use and
assumes all risks. Buyer's sole remedy shall be limited to the purchase price or replacement of product exclusive of labor or cost of labor.
NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL APPLY INCLUDING ANY WARRANTY OF MERCHANTIBILITY
OR FITNESS FOR A PARTICULAR PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGAL THEORY FOR
SPECIAL OR CONSEQUENTIAL DAMAGES. SIKA SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS PRODUCT IN
A MANNER TO INFRINGE ON ANY PATENT OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD BY OTHERS.
Sika Corporation Sika Canada Inc.
Porno Avenue 601, Delmar Avenue
Lyn .�
Lyndhurst, NJ 07071 Pointe -Claire, QC H9R 4A9 x_800.933-SIKA
Phone: (201) 933-BB00 Phone: (514) 697-2610
Fax: (201) 9336225 Fax: (514) 667-3087
wwwstkaconstruction.com wwwsika.ca
Regional Inrorrnation and Sales Centers. For the location of your nearest Sika representative, contact your regional center.
® U.S.: North East Region: Fairless Hills, PA, Phone: (215) 295.6600 North Central Region: Marton, OH, Phone: (800) 851-1545
South East Region: Conyers, GA, Phone: (770) 760-1300 South Central Region: Mesquite, TX, Phone: (972) 289.6480
Western Region: Santa Fe Springs, CA, Phone: (562) 9033650
Canada: Ontario: Mississauga, ON, Phone: (905) 795-3177, Alberta: Edmonton, AB, Phone: (780) 486.6111
Quality Certlllmdon Numbers: Lyndhurst FM 69711 (ISO 9000), FM 70421 (QS 9000), Martm: FM 69715, Kansan City: FM 69107, Santa Fe Spdngc FM 694M
Sika is a registered trademark Made in USA Printed in USA.
Product Data Sheet
Edition 10.2005
Identification no. 161
Plastocrete 161
Plastocrete®161
Water Reducing Admixture
Description Plastocrete 161 is a lignin polymer -type water -reducing admixture.
Plastocrete 161 meets the requirements of ASTM C-494 Types A, B and D.
Applications Plastocrete 161 is recommended for use in all applications where high quality
concrete with superior workability is required.
Advantages Plastocrete 161 water reducing admixture provides an economical and highly
effective means of reducing the amount of mixing water required to produce
concrete of a certain slump by acting as a dispersant for the cement particles
in the mix.
Through this dispersing action more of the surface area of the cement particles
is available for early hydration. The more cement particles hydrated by contact
with the mixing water, the greater the compressive strength of the concrete.
Plastocrete 161 is formulated as a Type A water reducer to allow up to 10%
water reduction and maximize the benefits of increased hydration in both the
hardened and plastic states.
■ Reduced water content required to achieve desired slump, increases
compressive and flexural strengths and allows the use of more economi-
cal mixes.
■ Improved paste quality makes concrete easier to pump and finish.
■ Consistent normal setting times throughout the recommended dosage.
■ Lower water cement ratios provide decreased permeability and increased
durability.
■ Plastocrete 161 does not contain intentionally added chlorides and will
not initiate nor promote the corrosion of steel in the concrete.
How to Use
Dosage Dosage rates will vary depending on the material used, ambient conditions
and the requirements of a specific project.
For general concreting applications, Sika recommends a dosage rate between
2-4 fl.oz./100 lbs. (130-260 ml/100 kg) of cementitious materials for normal
setting characteristics. Dosage rates of 4-6 fl.oz./100 lbs. (260-390 ml/100 kg)
of cementitious materials are recommended for applications where higher
water reduction is needed as well as extended workability and prolonged
setting times.
Dosage rates outside the recommended range may be used where
specialized materials such as microsilica are specified, extreme ambient
conditions are encountered or unusual project conditions require special con-
sideration. In this case please contact your local regional Sika office or Sika
® technical service department at 1-800-933-7452 for further information.
Packaging
Plastiment ES is available in 55 gallon drum (208 liter), 275 gallon totes
(1040 liters) and bulk delivery.
' j Storage and Shelf Life
Plastiment ES should be stored at above 40°F (50C). If frozen, thaw and agitate
a1
thoroughly to return to normal state.
Shelf life when stored in dry warehouse conditions between 40*F and 80eF
(50C - 270C) is one 1 year.
Typical Data
Appearance
Brown Liquid
p Specific Gravity
Approximately 1.2
CAUTION:
IRRITANT. Contains Carbohydrates (Mixture). Slightly irritating to the eyes and
skin.
Handling and Storage
Avoid direct contact. Wear personal protective equipment (chemical resistant
goggles/gloves/clothing) to prevent direct contact with skin and eyes. Use only in
well ventilated areas. Open doors and windows during use. Use a property fitted
'
NIOSH respirator if ventilation is poor. Wash thoroughly with soap and water after
use. Remove contaminated clothing and launder before reuse.
- j First Aid
Eyes — Hold eyelids apart and flush thoroughly with water for 15 minutes. Skin —
;a
Remove contaminated clothing. Wash skin thoroughly for 15 minutes with soap
and water. Inhalation — Remove to fresh air. Ingestion — Do not induce vomiting.
Dilute with water. Contact physician. In all cases contact a physician immedi-
ately if symptoms persist.
r' _{ Clean Up
Use personal protective equipment (chemical resistant gloves/goggles/clothing).
Without direct contact, sweep up spilled or excess product and place in suitable
sealed container. Dispose of excess product and container in accordance with
- s
applicable local, state, and federal regulations.
KEEP CONTAINER TIGHTLY CLOSED • KEEP OUT OF REACH OF CHILDREN • NOT FOR INTERNAL CONSUMPTION • FOR INDUSTRIAL USE ONLY
All information provided by Sika Corporation ('Sika') concerning Sika products, including but not limited to, any recommendations and advice
relating to the application and use of Sika products, is given in good faith based on Sika's current experience and knowledge of its products
when property stored, handled and applied under normal conditions in accordance with Sike's instructions. In practice, the differences in materi-
als, substrates, storage and handling conditions, actual site conditions and other factors outside or Sika's control are such that Slka assumes no
liability for the provision of such information, advice, recommendations or instructions related to its products, nor shall any legal relationship be
created by or arise from the provision of such information, advice, recommendations or instructions related to its products. The user of the Sika
product(s) must test the product(s) for suitability for the intended application and purpose before proceeding with the full application of the product(s).
Sika reserves the right to change the properties of its products without notice. All sales of Sika product(s)
are subject to its current terms and conditions of sale which are available at www.sikacorp.com or by calling 800-933-7452.
Prior to each use of any Sika product, the user must always read and fallow the wamings and instructions on the product's most cur-
rent Technical Data Sheet, product label and Material Safety Data Sheet which are available at www.sikaconstruction com or
800-933-7452. Nothing contained in any Sika materials relieves the user of the obligation to read and follow the wamings and instruction
for each Sika product as set forth in the current Technical Data Sheet, product label and Material Safety Data Sheet prior to product use.
SIKH warrants this product for one year from date of installation to be free from manufacturing defects and to meet the technical properties
on the current Technical Data Sheet if used as directed within shelf life. User determines suitability of product for intended use and
assumes all risks. Buyer's sole remedy shall be limited to the purchase price or replacement of product exclusive of labor or cost of labor.
NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL APPLY INCLUDING ANY WARRANTY OF MERCHANTIBILITY
OR FITNESS FOR A PARTICULAR PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGAL THEORY FOR
SPECIAL OR CONSEQUENTIAL DAMAGES. SIKA SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS PRODUCT IN
A MANNER TO INFRINGE ON ANY PATENT OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD BY OTHERS.
Sika Corporation
201 Polito Avenue
Lyndhurst, NJ 07071
Phone: (201)933-8800
Fax: (201)933-6225
wwwsikaconstrucdon.com
Sika Canada Inc.
601, Delmar Avenue
Pointe -Claire, QC H9R 4A9
Phone: (514)697-2610
Fax: (514) 697-3087
www.sika,ca
1-800-933-SIKA 0 @
�re�ira
Regional Information and Sales Centers. For the location of your nearest Sika representative, contact your regional center.
U.S.: North East Region: Fairless Hills, PA, Phone: (215) 295 -6600 North Cental Region: Marion, OH, Phone: (800) 851-1545
® South East Region: Conyers, GA, Phone: (770) 760-1300 South Central Region: Mesquite, TX, Phone: (972) 289-6480
® Western Region: Santa Fe Springs, CA, Phone: (562) 903-3650
Canada: Ontario: Mississauga, ON, Phone: (9D5) 795-3177, Alberta: Edmonton, AB, Phone: (780) 486-6111
QuaOty Cerdrloadm Numbers: Lyndhurst FM 69711 PS09000), FM 70421 (GS 9000), Merlon: FM 69715, Kmr.-. Chy: FM 69107, Sant. Fe Springs: FM 69406
Sika and Plastiment are registered trademarks. Made in USA. Printed in USA
Product Data Sheet
Edition 6.1.2009
Identification no.
Plastiment ES
Plastiment® ES
Water -reducing and Retarding Admixture
Description Plastiment ES is a water -reducing and retarding admixture. Plastiment ES meets
the requirements of ASTM C-494 as Types B and D and AASHTO M194 Types B
and D admixture.
Applications Plastiment ES should be used when a controlled delay in set time or increase in
slump life of concrete is desired. Plastiment ES can be utilized in concrete used
for flatwork and horizontal or vertical slipform placements. Use of Plastiment ES
provides a superior surface finish.
Benefits
• Improves slump life and delays set time of concrete
4,
• Slows down the rate of cement hydration reaction and controls concrete
temperature
i
■ Provides sufficient time for proper placement and finishing of concrete without
#,
cold joints in hot weather conditions
■ In flatwork applications, Plastiment ES acts as a finishing aid, improves work-
ability, controls bleeding and provides a superior surface finish
R�
• In mass concrete pours, Plastiment ES controls temperature rise and reduces
the risk of thermal cracking
■ Reduces permeability and enhances durability by allowing to reduce the water
cement ratio
Fx�>.
y..
• Improves early and later age compressive and flexural strength
=''a
• Improves homogeneity in the mix and reduces chances of segregation.
Refer to ACI 305R Hot Weather Concreting for more information. Plastiment ES
s -i
does rint COnt91n ralrh Im rhlnririp nr env nfhor intcn4innnlly niirlcrl nhlnrirlcc
How to Use
Dosage Dosage rates will vary depending on factors such as materials used, concrete
temperature, ambient temperature and specific requirements of the project.
For general concrete applications, Sika recommends a dosage rate of 2 - 4 fl.
oz./100 lbs. (130-260 ml/100 kg) of cementitious materials. Exact dosages for a
particular application should be determined by conducting trial mixes. Dosages
outside the recommended range can be used to meet specific project require-
ments after conducting trial mixes.
For more information please contact your local regional office or technical service
department at 1-800-933-7452.
Mixing Add Plastiment ES at the concrete plant. Measure required quantity manually or
by automated dispenser. Add into the water line at the batch plant or directly into
the concrete at the end of the mixing cycle. Do not mix with dry cement.
Combination with other admixtures: Plastiment ES is compatible with other
Sika admixtures. When used in combination with other admixtures, each
admixture should be added to the concrete separately.
Packaging Plastiment ES is available in 55 gallon drum (208 liter), 275 gallon totes
(1040 liters) and bulk delivery.
Storage and Shelf Life Plastiment ES should be stored at above 40'F (5eC). If frozen, thaw and agitate
thoroughly to return to normal state.
Shelf life when stored in dry warehouse conditions between 40°F and 80°F
(50C - 27eC) is one 1 year.
Typical Data
Appearance Brown Liquid
Specific Gravity Approximately 1.2
CAUTION: IRRITANT. Contains Carbohydrates (Mixture). Slightly irritating to the eyes and
skin.
:Handling and Storage
Avoid direct contact. Wear personal protective equipment (chemical resistant
K i i
goggles/gloves/clothing) to prevent direct contact with skin and eyes. Use only in
r
well ventilated areas. Open doors and windows during use. Use a properly fitted
k'
NIOSH respirator if ventilation is poor. Wash thoroughly with soap and water after
use. Remove contaminated clothing and launder before reuse.
First Aid
Eyes — Hold eyelids apart and flush thoroughly with water for 15 minutes. Skin
1
—
Remove contaminated clothing. Wash skin thoroughly for 15 minutes with soap
and water. Inhalation — Remove to fresh air. Ingestion — Do not induce vomiting.
Dilute with water. Contact physician. In all cases contact a physician immedi-
ately if symptoms persist.
}I Clean Up Use personal protective equipment (chemical resistant gloves/goggles/clothing).
j Without direct contact, sweep up spilled or excess product and place in suitable
Y r sealed container. Dispose of excess product and container in accordance with
applicable local, state, and federal regulations.
KEEP CONTAINER TIGHTLY CLOSED " KEEP OUT OF REACH OF CHILDREN " NOT FOR INTERNAL CONSUMPTION • FOR INDUSTRIAL USE ONLY
All information provided by Sika Corporation ("Sika") concerning Sika products, Including but not limited to, any recommendations and advic
relating to the application and use of Sika products, is given in good faith based on Sika's current experience and knowledge of its productse
when Property stored, handled and applied under normal conditions in accordance with Sike's instructions. In practice, the differences in materi-
als, substrates, storage and handling conditions, actual site conditions and other factors outside of Sike's control are such that Sika assumes no
liability for the provision of such information, advice, recommendations or instructions related to its products, nor shall any legal relationship be
created by or arise from the provision of such information, advice, recommendations or instructions related to its products. The user of the Sika
product(s) must test the product(s) for suitability for the intended application and purpose before proceeding with the full application of the pmduct(s).
Sika reserves the right to change the properties of its products without notice. All sales of Sika product(s)
are subject to its current terms and conditions of sale which are available at www.siKimro corn or by calling 800-933-7452.
Prior to each use of any Sika product. the user must always read and follow the warnings and instructions on the products most cur-
rent Technical Data Sheet, product label and Material Safety Data Sheet which are available at www ika on tructi- or
800. Nothing contained in any Sika materials relieves the user of the obligation to read and follow the warnings and instruction
for each Sika product as set forth in the current Technical Data Sheet, product label and Material Safety Data Sheet prior to product use.
SIKH warrants this product for one year from date of installation to be free from manufacturing defects and to meet the technical properties
on the current Technical Data Sheet if used as directed within shelf life. User determines suitability of product for intended use and
assumes all risks. Buyer's sole remedy shall be limited to the purchase price or replacement of product exclusive of labor or cost of labor.
NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL APPLY INCLUDING ANY WARRANTY OF MERCHANTIBILITY
OR FITNESS FOR A PARTICULAR PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGAL THEORY FOR
SPECIAL OR CONSEQUENTIAL DAMAGES. SIKA SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS PRODUCT IN
A MANNER TO INFRINGE ON ANY PATENT OR ANY OTHFH 1MTC11 CPTllnr
— Pvrauvn Sika Canada Inc.
201 Polito Avenue 601, Delmar Avenue
Lyndhurst, NJ 07071 Pointe -Claire, QC H9R 4A9 1-800-933-SIKA
Phone: (201) 9333800 Phone: (514) 697-2610
Fax: (201) 9333225 Fax. (514) 697-3087
wwwsikaconstruction.com www.sika,ca
Regional Information and Sales Centers. For the location of your nearest Sika representative, contact your regional center.
U.S.: North East Region: Fairless Hills, PA, Phone: (215) 295 3600 North Central Region: Marion, OH, Phone: (800) 851-1545
® South East Region: Conyers, GA, Phone: (770) 760-1300 South Central Region: Mesquite, TX, Phone: (972) 2893480
Western Region, Santa Fe Springs, CA, Phone: (562) 9033650
Canada: Ontario: Mississauga, ON, Phone: (905) 7953177, Alberta: Edmonton, AB, Phone: (780) 486.6111
Quality Certirication Numbers: l yndhumt FM 69711 (ISO 8000), FM 70421 (QS 9000), Marion: FM 60715, Kansas Clqr, FM 69107, Santa Fe Springs: FM 69408
Sika and Plastiment are registered trademarks. Made in USA Printed in USA