Prologis 5A/5B-SB180131
Submittal
Prologis One Twenty One Buildings 5A & 5B
Job No. 21001682
· Survoid Carton Form
· Bond Breaker
· Grout
· Concrete Cure
· Ultra Bond Epoxy
· Vapor Retarders
Structure Tone Southwest, Inc.
Review of these shop drawing or submittals does not
relieve the subcontractor of his responsibility for full
compliance with the plans, specifications, and contract
documents. Dimensions, quantities, errors, omissions,
and the furnishing of all items required, whether shown
on this drawing or not, shall remain the responsibility of
the subcontractor.
Submittal No. 030000-003 Job No. 21001682
Reviewed By: Colin Kimball Date: 01/31/18
America’s #1 Void Form System Protecting Concrete from Soil Expansion
1895 W. Dartmouth Ave.6151 Cowley Road 4555 Homestead Road
Englewood, CO 80110 Fort Worth, TX 76119 Houston, TX 77028
(303) 762-0324 (817) 429-0888 (281) 768-7340
(303) 762-9931 (Fax)(817) 429-7333 (Fax)(281) 768-7355 (Fax)
(800) 458-5444 (888) 803-8643 (866) 441-0315
LEED Certification Submittal Information
for Corrugated Paper Void Forms
What is LEED certification?
“In the United States and in a number of other countries around the world, LEED certification is the
recognized standard for measuring building sustainability. Achieving LEED certification is the best
way for you to demonstrate that your building project is truly "green."
The LEED green building rating system -- developed and administered by the U.S. Green Building
Council, a Washington D.C.-based, nonprofit coalition of building industry leaders -- is designed to
promote design and construction practices that increase profitability while reducing the negative
environmental impacts of buildings and improving occupant health and well-being.” (taken from the
Natural Resources Defense Council website: www.nrdc.org/buildinggreen/leed.asp)
Pertinent Information for Corrugated Paper Void Form Products:
Manufacturer:SureVoid Products, Inc.
6151 Cowley Road
Fort Worth, TX 76119
Corrugators:Packaging Corporation of America Packaging Corporation of America
1001 113th Street 2510 West Miller Road
Arlington, TX 76005 Garland, TX 75041
Primary Paper Mill: Packaging Corporation of America
6750 Highway 57
Counce, TN 38326
Harvest Location:Various forests in Tennessee, Mississippi, and Alabama
Recycled Content: Post-Consumer -- approx. 36.8% OCC (old corrugated containerboard)
Post-Industrial -- approx. 9.2% DLK (double-lined kraft / corrugator waste)
------------
46.0% Total
FSC Wood
Certification #:Various
Certified Wood:54% virgin fiber supplied from wood chips -- certified wood percentage unknown
1. Product Name
Stego Wrap 10-mil
Class A Vapor Retarder
2.Manufacturer
Stego Industries, LLC
27442 Calle Arroyo, Suite A
San Juan Capistrano, CA 92675
Sales, Technical Assistance
Ph: (877) 464-7834
Fx: (949) 493-5165
www.stegoindustries.com
3. Product Description
USES: Stego Wrap 10-mil is used as
an exceptional vapor retarder, and
as a protection course for below
grade waterproofing applications.
COMPOSITION: Stego Wrap 10-mil
is a multi-layer plastic extrusion
manufactured with only the highest
grade of prime, virgin, polyolefin
resins.
SIZE: Stego Wrap 10-mil comes in
rolls 14’ x 210’ or 2,940 ft2
WEIGHT: Stego Wrap 10-mil rolls
weigh approximately 141 lb.
4. Technical Data
APPLICABLE STANDARDS
American Society for Testing &
Materials (ASTM)
•ASTM E 1745 - Standard
Specification for Water Vapor
Retarders Used in Contact with
Soil or Granular Fill Under
Concrete Slabs
•ASTM D 882 - Test Methods for
Tensile Properties of Thin Plastic
Sheeting
•ASTM D 1709 - Test Methods for
Impact Resistance of Plastic Film
by Free-Falling Dart Method
•ASTM E 96 - Test Methods for
Wa ter Vapor Transmission of
Materials
•ASTM E 154 - Test Methods for
Wa t er Vapor Retarders Used in
Contact with Earth under
Concrete Slabs, on Walls, or as
Ground Cover
•ASTM E 631 - Terminology of
Building Constructions
Vapor Retarders
07260, 03300
•ASTM F 1249 - Test Method for
Wa ter Vapor Transmission Rate
Through Plastic Film and
Sheeting Using a Modulated
Infrared Sensor
•ASTM E 1643 - Standard Practice for
Installation of Water Vapor Retarders
Used in Contact with Earth or
Granular Fill Under Concrete Slabs
American Concrete Institute (ACI)
•ACI 302.1R-96 Minimum
Thickness (10-mils)
ENVIRONMENTAL FACTORS
Stego Wrap 10-mil can be used in
systems for the control of soil gases
(radon, methane), soil poisons
(oil by-products) and sulfates.
5. Installation
UNDERSLAB: Unroll Stego Wrap
10-mil over an aggregate, sand or
tamped earth base. Overlap all
seams a minimum of 6” and tape
using Stego Tape. All penetrations
must be sealed using a combination
of Stego Wrap, Stego Tape and/or
Stego Mastic.
VERTICAL WALL: Install Stego Wrap
10-mil over the waterproofing
membrane while still tacky.
Mechanically fasten Stego Wrap to
the wall at the top with termination
bar and concrete nails. Drape Stego
Wrap down across the footer and
under the french drain.
6. Availability & Cost
Stego Wrap 10-mil is available
nationally via building supply
distributors. For current cost
information, contact your local
Stego Wrap distributor or Stego
Industries’ sales department.
7. Warranty
Stego Industries, LLC believes to the
best of its knowledge, that
specifications and recommend-
ations herein are accurate and
reliable. However, since site
conditions are not within its control,
Stego Industries does not guarantee
results from the use of the
information provided and disclaims
all liability from any loss or damage.
No warranty, express or implied, is
given as to the merchantability,
fitness for a particular purpose, or
otherwise with respect to the
products referred to.
8. Maintenance
None required.
9.Technical Services
Technical advice, custom CAD
drawings, and additional
information can be obtained by
contacting Stego Industries’
technical assistance department or
via the website:
www.stegoindustries.com
10.Filing Systems
• SpecSource
• Stego Industries’ website
• MasterSpec
STEGO DATATABLE 1: PHYSICAL PROPERTIES OF STEGO WRAP 10-MIL VAPOR RETARDER
Property & Test Stego Wrap 10-Mil
Underslab Vapor Retarders, ASTM E 1745 Class A, B & C Exceeds
Water Vapor Permeance, ASTM E 96 & ASTM F 1249 0.036 perms
Tensile Strength, ASTM D 882 54.4 lbf./in.
Puncture Resistance, ASTM D 1709 2340 grams
Chemical Resistance, ASTM E 154 Unaffected
Life Expectancy, ASTM E 154 Indefinite
STEGO INDUSTRIES, LLC
Stego®Wrap 10-mil Class A
10/03
Technical Data
For Commercial/Industrial Use Only
PRODUCT DESCRIPTION:
Sure-Lift (J-6) is a premium grade bondbreaker that also acts as a
cure for tilt-up construction. Sure-Lift is a long chain chemically
reactive compound that will not interfere with the bondability of
paints and coatings designed for exterior concrete when applied
according to their manufacturer’s instructions. The organic com-
pounds in Sure-Lift react with the lime in the concrete. During the
chemical reaction, a gel is produced in the surface pores of the con-
crete slab forming a water impermeable barrier. This impermeable
barrier restricts mix water (which is needed for hydration) from being
absorbed into the casting slab. The resulting downside surface of the
panel will be stronger and have a more uniform, cleaner appearance.
Sure-Lift contains a fugitive dye to aid in the application. Once an
application of Sure-Lift is dry, it resists light abrasion caused by foot
traffic during the setting of reinforcing steel.
PURPOSE:
As a bondbreaker, Sure-Lift is unsurpassed in providing a clean, easy
lift. In performance testing, Sure-Lift required less pounds of pres-
sure to release and lift panels than other major brands. Properly
applied, Sure-Lift will not transfer to or stain the panels. Painting of
the panels can be performed as soon as the moisture content in the
concrete is at an acceptable level for the paint manufacturer. Sure-Lift
is more resistant to rain and weather than resin based bondbreakers.
ADVANTAGES:
•Chemically reactive
•Panels lift easier
•Resists rain and weather, less reapplication
•Clean panels, no resin stains
•Reduces waiting period for painting
•Resists construction foot traffic abrasion
•Saves money, covers more ft2 per gallon than typical membrane
forming bondbreakers
•Contains a fugitive dye for ease of application
APPLICATION INSTRUCTIONS:
Curing New Concrete:
The use of the Day-Chem Cure & Seal: (J-22 or J-23)
@ 300-400 ft2/gal (7.4-9.8 m2/L) provides a membrane forming cure
meeting ASTM C-309, as well as a curing membrane that is compati-
ble with Sure-Lift. However, Sure-Lift can also be used to cure the
concrete slab. The timely application of the cure coat is critical to the
successful lifting of the panels.
Curing should commence immediately after the final steel troweling
and when surface water has disappeared.
Bondbreaker Coat:
Pour areas must be smooth, dense and well cured. Clean area to be
treated by sweeping or with compressed air. Just prior to placing
reinforcing steel and within two weeks of pouring panels, spray apply
Sure-Lift at 400 ft2/gal. (9.8 m2/L) to the point of rejection. Spray at
right angles to curing compound spray pattern. Wait until dry, a min-
imum of two hours, and apply a second coat at right angles to previ-
ous coat. Coverage will typically be 550 to 700 ft2/gal. (13.5 to 17.2
m2/L). If light or white spots appear within 10-40 minutes after spray-
ing, those areas are extra porous and should be fogged with water
and resprayed with Sure-Lift. Due to slab variables, such as mix
designs and slab porosity, actual coverage rate can only be deter-
mined by the presence of a soap-like feel over the entire slab. Sure-
Lift should not be over applied. Puddles and excess material must be
avoided. Wipe up excess material with squeegee or rags. Do not walk
on areas sprayed with Sure-Lift until dry. Do not apply below 35°F.
(2°C) Do not apply Sure-Lift over frost or standing surface water.
Wait until completely dry before pouring concrete.
Casting Over Old Concrete:
When casting over old concrete where Sure-Lift was not used as the
curing compound, be sure the concrete is smooth, dense, clean and
suitable for pouring panels. It is essential that a membrane of Sure-
Lift is formed at the surface prior to placing reinforcing steel and
within two weeks of pouring panels. Flood slab with water and push
off excess with squeegee. Immediately apply Sure-Lift over damp
slab to point of rejection, 300 to 500 ft2/gal. (2.8-12.3 m2/L) . After
drying, apply a second coat of Sure-Lift to point of rejection at 400 to
500 ft2/gal. (9.8-12.3 m2/L). The second coat should be applied at
right angles to the first coat. If light or white spots appear within 20-
40 minutes, reapply Sure-Lift. If light or white spots persist, fog with
water and reapply.
Before Pouring:
Always test casting slab by sprinkling a few drops of water on slab in
various places. Water should bead as if on a waxed car. The entire
treated slab must have a soap-type feel to the touch. If there have
been heavy showers, heavy foot traffic or excessive time lapse, test
water may soak into slab. This would necessitate pulling steel and
respraying. For optimal performance, flood area with water (1/8"
layer) immediately before pouring, then squeegee off excess water.
Hot Weather Procedures:
In hot weather, prior to the first bondbreaker application, flood the
slab with water to reduce its porosity and to cool it down. After
soaking the slab, squeegee off the excess water, removing all the
free water on the surface, then proceed to apply the first bondbreaker
coat. This procedure will allow the bondbreaker to remain on the sur-
face and not be absorbed into the slab. Even more critical is to flood
the pour area with water (1/8" layer) immediately before
pouring concrete.
Exposed Aggregate:
For sand-bed-exposed aggregate panels, spray sand with Sure-Lift at
11/03 2-5
SURE-LIFTTM (J-6) & SURE-LIFT FAST DRYTM (J-6)
Premium Bondbreaker Dayton SuperiorChemical & Cement Products3
CONCRETE
Technical Data
300 ft2/gal. (2.8 m2/L) Then rake the sand and spray Sure-Lift again
at 300 ft2/gal. (2.8 m2/L) Compact sand. Let dry 2 to 3 hours then
place aggregate. Do not disturb the sand during placement of aggre-
gate.
Stack Panels:
In general, care must be used when applying bondbreaker to stack
panels. Stack panels tend to transfer water faster across their inter-
face thus leading to sticking. It is recommended that a membrane
forming cure and seal (J-22 or J-23) be applied prior to the bond-
breaker between each layer to lessen the chance of sticking.
Painting & Coatings:
Provided that Sure-Lift has not been over applied, painting of the
panels can be performed as soon as the moisture content in the con-
crete is at an acceptable level for the paint manufacturer. Check with
the paint manufacturer for recommendations. Migrating moisture
from the concrete panel, not Sure-Lift, may cause the paint to blister.
Painting and coating manufacturer’s instructions for preparation and
application of their product supersede information herein.
APPROXIMATE COVERAGE:
Sq. Feet per Gallon Sq. Meters per Liter
Cure:
(Smooth Finish) 400 9.8
Bondbreaker:
First Coat:
(Smooth Finish) 400 9.8
Second Coat:
(Smooth Finish) 550 – 700 13.5 – 17.2
Rate is dependent on slab porosity, wind and temperature.
DRYING TIME:
2 Hours at 70° F (21°C)
PACKAGING:
55 gal. drums (208L) and 5 gal. pails (18.9L)
CLEANUP:
Tools / Equipment use: mineral spirits,
naphtha, xylol
LIMITATIONS:
Wait until Sure-Lift is completely dry before pouring concrete. Do not
apply to reinforcing steel. Avoid over application. Wipe up puddles
with squeegee or rags. Do not walk on Sure-Lift until dry. If rain
occurs while Sure-Lift is drying, check for reapplication. For optimal
performance, flood the pour area with water (1/8" layer) immediately
before pouring concrete. Shelf life for unopened containers is one
year. Do not apply below 35°F (2°C).
WARNING:
•Use with adequate ventilation
•Keep out of the reach of children
•Do not take internally
•In case of ingestion, CALL A PHYSICIAN immediately.
DO NOT induce vomiting
Flammable Mixture. If splashed in the eyes, flush thoroughly with
clean water for a minimum of 15 minutes. CALL A PHYSICIAN
immediately. May cause irritation to the skin. If brought into contact
with the skin, wash thoroughly with soap and water. Seek medical
attention if redness or irritation occurs. Avoid breathing vapors and
spray mist. Keep away from heat, spark, open flame and other possi-
ble sources of ignition. Reseal container after each use. Wear protec-
tive clothing, gloves, and goggles. May contain mineral spirits. Safe
disposal of rags is necessary to avoid possibility of spontaneous
combustion. Read MSDS before using product.
TECHNICAL SERVICES:
Contact the technical staff for assistance at:
1-866-329-8724 • 1-913-233-1750 • FAX: 1-913-279-4806
daytonsuperiorchemical.com
WARRANTY
Warranty, Warranty Disclaimer and Exclusive Remedy – Dayton Superior Corporation warrants, for 12 months from
the date of manufacture or for the duration of the published product shelf life, whichever is less, that at the time of
shipment by (“the Company”), the product is free of manufacturing defects and conforms to (“the Company’s”) pub-
lished specifications in force on the date of acceptance by (“the Company”) of the order. (“the Company”) shall only
be liable under this warranty if the material has been applied, used, and stored in accordance with (“the Company”)
instructions in the product’s technical data sheet.
The purchaser must examine the product when received and promptly notify (“the Company”) in writing of any non-
conformity before the product is used, or no later than 30 days after such non-conformity is first discovered. If (“the
Company”), in its sole discretion, determines that the product breached the above warranty, it will, in its sole dis-
cretion, replace the non-conforming product, refund the purchase price or issue a credit in the amount of the pur-
chase price. This is the sole and exclusive remedy for breach of this warranty.
Only a (“Company”) officer is authorized to modify this warranty. The sales information on the (“the Company’s”)
website and received by the customer during the sales process does not supersede this warranty and the specifica-
tions of the product in force on the date of sale. THE FOREGOING WARRANTY SHALL BE EXCLUSIVE AND IN LIEU
OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FIT-
NESS FOR A PARTICULAR PURPOSE AND ALL OTHER WARRANTIES OTHERWISE ARISING BY OPERATION OF
LAW, COURSE OF DEALING, CUSTOM, TRADE OR OTHERWISE.
Limitation of Liability – Dayton Superior Corporation shall not be liable in contract or in tort (including, without
limitation, negligence, strict liability or otherwise) for loss of sales, revenues or profits; cost of capital or funds;
business interruption or cost of downtime, loss of use, damage to or loss of use of other property (real or person-
al); failure to realize expected savings; frustrations of economic or business expectations; claims by third parties
(other than for bodily injury), or economic losses of any kind; or for any special, incidental, indirect, consequential,
punitive or exemplary damages arising in any way out of the performance of, or failure to perform, this Agreement,
even if (“the Company”) could foresee or has been advised of the possibility of such damages. The Parties express-
ly agree that these limitations on damages are allocations of risk constituting, in part, the consideration for this
agreement, and also that such limitations shall survive the determination of any court of competent jurisdiction that
any remedy provided in these terms or available at law fails of its essential purpose.
Dayton Superior Specialty Chemical Corp • 4226 Kansas Avenue, Kansas City, KS 66016
Telephone (913) 233-1750 • Fax (913) 279-4806 • daytonsuperiorchemical.com
For Commercial/Industrial Use Only 11/032-6Dayton SuperiorChemical & Cement Products3
CONCRETE
The Euclid Chemical Company
www.euclidchemical.com19215 Redwood Road • Cleveland, OH 44110
800-321-7628 t • 216-531-9596 f GroutsNS GROUTMaster Format #:03 62 13NS GROUT
Non-shrink, Non-staining, Non-metallic Grout
Description
NS GROUT is designed for critical use where high strength, non-staining characteristics and positive expansion
are required. NS GROUT contains only natural aggregate and an expansive cementitious binder. It is extremely
flowable. When cured, it appears similar to concrete in appearance.
Primary Applications
• Pumps and fans
• Compressors & motors
• Generators
• Machine bases of all types
• Anchor bolts
• Column baseplates
Features/Benefits
• Non-staining natural aggregate for better
appearance
• Excellent bearing
• Compatible with galvanic anodes (Fluid)
• Appearance of plain concrete
• Does not contain any added chloride ions
• Outstanding strength
Shelf Life
2 years in original, unopened package
Technical Information
Packaging/Yield
NS GROUT 50 lb (22.7 kg) with 25 lbs (11.3 kg) of 3/8” (9.5 mm) pea gravel will yield approximately 0.60 ft3
(0.017 m3) of flowable consistency grout. Use pea gravel for deep fills over 5” (12.7 cm) only.
NS GROUT is packaged in 50 lb (22.7 kg) bags and pails. 50 lbs yields 0.45 ft3 (0.013 m3) of fluid grout when
mixed with 1.2 gal (4.5 L) of water.
* See ASTM C 1107 Section 11.5
Property Flowable Consistency Fluid Consistency
Flow Rate
(ASTM C939/CRD C621)120% (Flow Table)20 to 30 seconds (Flow
Cone)
Compressive Strength
(A STM C109 M od i f i ed *)
2 in (50 mm) cubes
3 days 4500 psi (31 MPa)
7 days 6000 psi (41 MPa)
28 days 8500 psi (59 MPa)
3 days 3500 psi (24 MPa)
7 days 5000 psi (34 MPa)
28 days 6800 psi (47 MPa)
Expansion (CRD C621)
3 days 0.02%
7 days 0.02%
14 days 0.03%
28 days 0.03%
3 days 0.01%
7 days 0.03%
14 days 0.05%
28 days 0.05%
Setting Time Initial Set 3 to 5 hours
Final Set 4 to 6 hours
Material properties tested under laboratory conditions @ 75oF (24oC), 50% RH
WARRANTY: The Euclid Chemical Company (“Euclid”) solely and expressly warrants that its products shall be free from defects in materials and workmanship for one (1) year from the date of purchase. Unless authorized
in writing by an officer of Euclid, no other representations or statements made by Euclid or its representatives, in writing or orally, shall alter this warranty. EUCLID MAKES NO WARRANTIES, IMPLIED OR OTHERWISE,
AS TO THE MERCHANTABILITY OR FITNESS FOR ORDINARY OR PARTICULAR PURPOSES OF ITS PRODUCTS AND EXCLUDES THE SAME. If any Euclid product fails to conform with this warranty, Euclid will replace the
product at no cost to Buyer. Replacement of any product shall be the sole and exclusive remedy available and buyer shall have no claim for incidental or consequential damages. Any warranty claim must be made within
one (1) year from the date of the claimed breach. Euclid does not authorize anyone on its behalf to make any written or oral statements which in any way alter Euclid’s installation information or instructions in its product
literature or on its packaging labels. Any installation of Euclid products which fails to conform with such installation information or instructions shall void this warranty. Product demonstrations, if any, are done for illustrative
purposes only and do not constitute a warranty or warranty alteration of any kind. Buyer shall be solely responsible for determining the suitability of Euclid’s products for the Buyer’s intended purposes.
Rev. 05.15
Directions for Use
Note: The contractor and engineer are encouraged to consult and review the Euclid Chemical bulletin: "Cementitious Grout
Application Guide". The document offers instructions detailing the general installation of Euclid Chemical manufactured
cement-based grout products. Important: If the contractor is not familiar with standard grout placement techniques, a pre-
job meeting is suggested to review the project details unique to the particular job. Contact your local Euclid Chemical
representative for additional information.
Mixing Consistency: Estimated Water Content*
Fluid 1.1 to 1.2 gal/50 lb bag (4.2 to 4.5 L/22.7 kg)
Flowable 0.9 to 1.0 gal/50 lb bag (3.4 to 3.8 L/22.7 kg)
Plastic 0.8 to 0.9 gal/50 lb bag (3.0 to 3.4 L/22.7 kg)
* Do not add water in an amount that will cause bleeding or segregation. More or less water may be required to achieve a 25
second flow or the desired placing consistency, depending on temperature and other variables. Do not add sand or cement
to the grout since this action will change its precision grouting characteristics.
Where NS GROUT will be placed at a thickness over 5" (12.7 cm), up to 25 lb (11.3 kg) of pea gravel must be
added to each bag of grout. Note that the water demand to achieve a certain flow level of the grout will change.
Once the correct amount of water has been added to a clean mixing pail, mix the grout with a high speed drill
and mixing paddle for 3 minutes. Quickly transport the grout to the placement area.
Placing: NS GROUT sets more rapidly than plain mortars; therefore, place quickly and continuously. If placing
this product in hot weather, the use of cold water will increase the working time.
Curing and Sealing: Proper curing procedures are important to ensure the durability and quality of the grout.
Wet cure the grout until the forms are stripped. Cure the grout with a high solids curing compound, such as
SUPER REZ-SEAL or SUPER AQUA-CURE VOX.
Clean-Up
Clean tools and equipment with water before the material hardens.
Precautions/Limitations
• Do not add sufficient water to promote bleeding of the grout.
• Do not use this product at a flow cone rate of less than 20 seconds if checking flow rates on the job site (see
CRD C-611 or ASTM C 939 for flow cone method).
• Do not add any admixture or fluidifiers.
• Proper curing is required.
• Do not use material at temperatures that may cause premature freezing.
• Rate of strength gain is significantly affected at temperature extremes.
• Do not allow grout to freeze until 4000 psi (27.6 MPa) is attained.
• Employ cold or hot weather grouting practices per ACI guidelines as the temperature dictates.
• Store materials in a dry place.
• For dry pack applications, mechanically mix NS GROUT at a minimum water content of 0.5 gal/50 lb bag (1.9
L/22.7 kg)
• Add pea gravel when placing at a thickness greater than 5” (12.7 cm).
• In all cases, consult the Safety Data Sheet before use.
• Fully complies with ASTM C 1107, Standard Specification for Packaged Dry, Hydraulic-Cement Grout
• Canadian MTQ
Specifications/Compliances
• Fully complies with CRD C 621, Corps of Engineers Specification for Non-Shrink Grout
NS GROUT is a free flowing powder designed to be mixed with water. After mixing and placing, the color may
initially appear much darker than the surrounding concrete. While this color will lighten up substantially as it
cures and dries out, the grout may always appear somewhat darker than the surrounding concrete.
Appearance
DESCRIPTION
Shep Cure 309 Rez All water-based concrete curing com-
pound is formulated from hydrocarbon resins and may be
used on interior, exterior, vertical, and horizontal concrete
surfaces. Once applied, Shep Cure 309 Rez All forms a liq-
uid membrane that retains an optimum amount of water in
freshly placed concrete for complete hydration of the cement.
NOTE: After approximately four weeks, the membrane
begins to chemically break down. The membrane will even-
tually dissipate from the surface. This process usually takes
another 3 - 5 weeks under normal traffic, exposure to UV,
and weathering conditions.
PRIMARY APPLICATIONS
Shep Cure 309 Rez All has been used on both interior and
exterior applications where paint, resilient tile or resilient
flooring may be applied later. Because of the wide variety of
coatings, paints, adhesives, and toppings available, contact
the manufacturer of the flooring system or subsequent coat-
ing or topping for application approval over resin-based
curing compounds. A small test application is always rec-
ommended.
FEATURES & BENEFITS
When properly applied, Shep Cure 309 Rez All produces
a premium-grade film, which optimizes water retention.
Furnished as a ready-to-use, true water-based com-
pound.
Produces hard, dense concrete -- minimizes hair checking,
thermal cracking, dusting, and other defects.
Offers a compressive strength significantly greater than
improperly or uncured concrete.
Increases tensile strength for greater resistance to cracking
and surface crazing.
Improves resistance to abrasion and the corrosive actions
of salts and chemicals.
Minimizes excessive shrinkage.
Can be applied quickly and easily with conventional com-
mercial spray equipment.
Formulations are also available with red fugitive dye
added.
VOC compliant -- VOC content is <100 g/L.
TECHNICAL DATA
Drying Time: Typically dries in 1- 2 hours, depending on
jobsite conditions (temperature, wind, etc.) Restrict foot traf-
fic for at least four hours; 12 hours is preferable.
Flash Point: >210ºF (99º C).
Coverage: Approximately 200 ft.²/gal. (4.91 m²/L).
LEED INFORMATION
May help contribute to LEED credits:
EQ Credit 4.2: Low-Emitting Materials: Paints & Coatings
MR Credit 5.1: Regional Materials: 10% Extracted, Pro-
cessed & Manufactured Regionally
MR Credit 5.2: Regional Materials: 20% Extracted, Pro-
cessed & Manufactured Regionally
COMPLIANCES
ASTM C 309, Type 1, Classes A & B (Type 1-D also avail-
able)
AASHTO M 148, Type 1, Classes A & B (Type 1-D also
available)
U.S. EPA Architectural Coatings Rule: 350 g/L maximum
VOC for concrete curing compounds
SCAQMD Rule 1113: 100 g/L maximum VOC for con-
crete curing compounds and waterproofing concrete/
masonry sealers
Ozone Transport Commission (OTC): 350 g/L maximum
VOC for Concrete Curing Compounds
Continued on reverse side
800-729-1150 | www.cmcsheplers.com 777 Eldridge Pkwy., Ste. 500, Houston, TX 77079 PRODUCT INFORMATION TECHNICAL DATA SHEETSHEP CURE 309 REZ ALL
CONCRETE CURING COMPOUND
SHEP CURE 309 REZ ALL4
DIRECTIONS FOR USE
Preparation: Application equipment must be clean and free
of all previously used materials.
Mixing: For optimum performance, gentle mixing or agita-
tion is recommended. CAUTION: TO AVOID FOAMING,
DO NOT MIX EXCESSIVELY. In the container, the curing
compound appears ivory in color; however, it dries to a
clear, transparent coating with a very slight amber tint.
Application: Apply in a uniform film to horizontal surfaces as
soon as the surface water disappears and the surface will not
be marred by walking workmen. On vertical surfaces, apply
promptly after the forms are removed. Shep Cure 309 Rez
All may be applied with a typical commercial hand or power
sprayer. Use a Shepler’s Performance Products sprayer that
produces a flow of 1/2 gal. (1.89 L) per minute under 40 psi
(.276 MPa) of pressure.
Cleanup: Prior to drying, cleanup can be accomplished with
soap and water. Once dried, use mineral spirits or other
suitable petroleum solvent.
PACKAGING
5 gallon pails and 55 gallon drums
SHELF LIFE (TYPICAL)
One year in original, unopened container.
LIMITATIONS
KEEP FROM FREEZING. Do not apply if air and/or concrete
temperature is less than 40° F (4°C). Improper or over-appli-
cation may increase the amount of time necessary for the
film to dissipate from the surface. SURFACE MAY DISCOLOR
AND/OR YELLOW DUE TO OVERAPPLICATION. DO NOT
MIX OR DILUTE WITH ANY OTHER PRODUCTS OR LIQ-
UIDS. Do not apply paint, resilient flooring or any other
subsequent coatings or toppings without first checking the
specifications and securing approval from the manufacturer
of the product being applied over Shep Cure 309 Rez All. A
small test application is always recommended. If removal of
Shep Cure 309 Rez All is necessary, use a degreaser.
PRECAUTIONS
Direct contact may result in mild irritation. Read and fol-
low all application, precaution, label, and health and safety
information prior to use. Refer to Material Safety Data Sheet
for complete health and safety information.
LIMITED WARRANTY: NOTICE - READ CAREFULLY. CONDITIONS OF SALE.
Manufacturer offers this product for sale subject to, and Buyer and all users are
deemed to have accepted, the following conditions of sale and limited warranty
which may be varied by written agreement of a duly authorized corporate officer of
Manufacturer. No other representative of or for Manufacturer is authorized to grant
any warranty or to waive limitation of liability set forth below.
Warranty Limitation: Manufacturer warrants this product to be free of manufacturing
defects. If the product when purchased was defective and was within use period
indicated on container or carton, when used, Manufacturer will replace the defective
product with new product without charge to the purchaser. Manufacturer makes NO
OTHER WARRANTY, either expressed or implied, concerning this product. There is
NO WARRANTY OF MERCHANTABILITY. In no case shall Manufacturer be liable for
special, indirect or consequential damages resulting from the use or handling of the
product, and no claim of any kind shall be greater in amount than the pur chase price
of the product in respect of which damages are claimed.
Inherent Risk: MANUFACTURER MAKES NO WARRANTY TO THE PERFORMANCE
OF THE PRODUCT AFTER IT IS APPLIED BY THE PURCHASER, AND PURCHASER
ASSUMES ALL RISKS ASSOCIATED WITH THE USE OR APPLICATION OF THE
PRODUCT.PRODUCT INFORMATION TECHNICAL DATA SHEETSHEP CURE 309 REZ ALL800-729-1150 | www.cmcsheplers.com 777 Eldridge Pkwy., Ste. 500, Houston, TX 77079
4
Manufactured In The U.S.A. by Adhesives Technology Corp.
450 East Copans Road ■ Pompano Beach, FL 33064 ■ (800) 892-1880 ■ Fax (800) 362-3320 ■ www.atc.ws
Revised: 06/2008 Page 1 of 5
Ultrabond 1300
1. Product Name
Ultrabond 1300 Epoxy Anchoring Gel
2. Manufacturer
Adhesives Technology Corp.
450 East Copans Road
Pompano Beach, FL 33064
(800) 892-1880
(954) 782-2221
Fax: (800) 362-3320
E-mail: info@atc.ws
Web Address: www.atc.ws
3 . Product Description
GENERAL DESCRIPTION
Ultrabond 1300 Epoxy Anchoring
Gel is a two component (1:1 ratio),
100% solids, high modulus,
structural, epoxy gel. It is a solvent
free, no odor, high strength, moisture
insensitive, non-sag epoxy system.
Ultrabond 1300 has exceptional
strength, maximum field reliability,
along with a high heat deflection
temperature of 131 degree’s
Fahrenheit which provides engineers
and contractors with a choice for
specifying and setting adhesive
anchors in elevated temperature
environments. In addition,
Ultrabond 1300 has a long working
time of 20 minutes, while also
providing an anchor that can be
loaded in as little as 2 hours (at 75°
F.) This allows contractors enough
time to set the anchors without
worrying about gelling too fast.
1/2" threaded rod at *9D in 3,000 psi concrete.
*9D is the embedment depth of the anchor (9 x 1/2");
in this example, a 1/2" threaded rod embedded 4-1/2”
in 3,000 psi concrete.
Quick Selection Guide
Tension Load (1/2”) 14,146 lbs. *
Working Time (75°) 20 min
Cure Time (75°) 2 hrs
Temperature Range 40°F - 110°F
BASIC USE
Acceptable uses for Ultrabond 1300 include rebar dowel and
anchor installations where dynamic, vibratory or intermittent loads
exist. Ultrabond 1300 has not been tested and is not for use in
overhead applications or applications that have long term
sustained loads at elevated temperatures. Typical applications
clude: in • Fastening in grout filled block and unreinforced masonry
• Seismic anchoring and bracing
• Grouting dowel bars and tie bars for full-depth concrete
pavement repairs
• Bonding raised pavement markers to concrete or asphalt
• Pick proof sealant – windows, doors, locks, etc. (e.g. correctional
facilities)
• Capping paste for crack-injection
COLOR
“A” Component (Resin): White
“B” Component (Hardener): Black
M ixed: Concrete Gray
SHELF LIFE: 2 Years
SIZE/PACKAGING
C artridge Sizes: Ultrabond 1300 is available in:
• 9 oz. cartridges; part number A9-1300
• 22 oz. cartridges; part number A22-1300N
• 53 oz. cartridges; part number A53-1300 The resin and hardener are uniformly dispensed from a dual
cartridge system and mixed simultaneously through a mixing
nozzle, providing contractors with a self mix delivery system.
B ulk Sizes: Ultrabond 1300 is available in bulk sizes, including:
• 1 gallon kit (102 fl. oz.); part number BUG-1300
• 2 gallon kit; part number; B2G-1300
• 10 gallon kit; part number; B10G-1300
• 100 gallon kit; part number; B100G-1300
4. Technical Data
American Society for Testing Materials (ASTM)
M eets ASTM C881, Type I, II, IV, & V, Grade 3, Class B & C
IInnddeepp ee nnddeenntt AASSTTMM CC888811--9999
TTee cchhnnii ccaall DDaatt aa
Properties ASTM Results
Compressive Yield Strength - psi D695 11,890 (7 day)
Compressive Modulus – psi D695 201,280 (7 day)
Tensile Strength - psi D638 7,428 (7 day)
Elongation - % D638 1.8 (7 day)
Bond Strength C882 1,410 (2 day)
Bond Strength C882 2,340 (14 day)
Consistency C881 Non-Sag Gel
Heat Deflection Temperature - °F D648 131 (7 day)
Water Absorption - % D570 0.52 (24 hours)
Linear Coefficient of Shrinkage D2566 0.004
Manufactured In The U.S.A. by Adhesives Technology Corp.
450 East Copans Road ■ Pompano Beach, FL 33064 ■ (800) 892-1880 ■ Fax (800) 362-3320 ■ www.atc.ws
Revised: 06/2008 Page 2 of 5
Ultrabond 1300
TENSION LOADS FOR THREADED RODS
f’c = 3000 psi f’c = 5000 psi f’c = 7000 psi
Threaded
Rod
Diameter
(in.)
Hole
Diameter
(in.)
Minimum
Embedment
Depth
(in.)
Ultimate
Tension
Load
(lbs)
Allowable
Tension
Load
(lbs)
Ultimate
Tension
Load
(lbs)
Allowable
Tension
Load
(lbs)
Ultimate
Tension
Load
(lbs)
Allowable
Tension
Load
(lbs)
3/8 7/16 3-3/8 9,336 2,334 10,124 2,531 10,936 2,734
1/2 9/16 4-1/2 14,146 3,537 14,512 3,628 18,400 4,600
5/8 3/4 5-5/8 19,600 4,900 20,688 5,172 29,288 7,322
3/4 7/8 6-3/4 25,052 6,263 26,864 6,716 34,764 8,961
7/8 1 7-7/8 33,376 8,344 34,328 8,582 39,524 9,881
1 1-1/8 9 41,696 10,424 41,792 10,448 52,144 13,036
Safety Factor “Allowable” equals 25% of Ultimate Load, 32% for steel
SHEAR LOADS FOR THREADED RODS
f’c = 3000 psi f’c = 5000 psi f’c = 7000 psi
Threaded
Rod
Diameter
(in.)
Hole
Diameter
(in.)
Minimum
Embedment
Depth
(in.)
Ultimate
Tension
Load
(lbs)
Allowable
Tension
Load
(lbs)
Ultimate
Tension
Load
(lbs)
Allowable
Tension
Load
(lbs)
Ultimate
Tension
Load
(lbs)
Allowable
Tension
Load
(lbs)
3/8 7/16 3-3/8 6,940 1,735 7,036 1,759 7,144 1,786
1/2 9/16 4-1/2 8,316 2,079 10,380 2,595 13,096 3,274
5/8 3/4 5-5/8 15,328 3,832 18,056 4,514 19,052 4,763
3/4 7/8 6-3/4 22,336 5,584 25,732 6,433 26,072 6,518
7/8 1 7-7/8 29,364 7,341 31,408 7,852 33,092 8,273
1 1-1/8 9 36,396 9,099 37,084 9,271 40,952 10,238
Safety Factor “Allowable” equals 25% of Ultimate Load, 32% for steel
Manufactured In The U.S.A. by Adhesives Technology Corp.
450 East Copans Road ■ Pompano Beach, FL 33064 ■ (800) 892-1880 ■ Fax (800) 362-3320 ■ www.atc.ws
Page 3 of 5
Ultrabond 1300
UULLTTRRAABBOONNDD 11330000 CCuurree SScchheedduullee
TTeemmppeerraattuurree WWoorrkkiinngg BBoolltt--UUpp
°°CC °°FF TTiimmee TTiimmee
4.4° C. 40° F. 40 min 24 hrs
12.8° C. 55° F. 30 min 14 hrs
18.3° C. 65° F. 20 min 6 hrs
23.8° C. 75° F. 13 min 2 hrs
29.4° C. 85° F. 10 min 2 hrs
35.0° C. 95° F. 7 min 2 hrs
ESTIMATING / USAGE GUIDES
RRoodd
DDiiaa
HHoollee
DDiiaa
UULLTTRRAABBOONNDD 11330000 UUssaaggee EEssttiimmaattee GGuuiiddee –– 2222 oozz.. CCaarrttrriiddggee SSyysstteemm –– TThhrreeaaddeedd RRoodd
EEmmbbeeddmmeenntt DDeepptthh ((iinn..))
((iinn..)) ((iinn..)) 22 33 44 55 66 77 88 99 1100 1111 1122 1133 1144 1155 1166 1177
3/8 7/16 211.3 140.9 105.6 84.5 70.4 60.4 52.8 47.0 42.3 38.4 35.2 32.5 30.2 28.2 26.4 24.9
1/2 9/16 159.8 106.5 79.9 63.9 52.5 45.6 39.9 35.5 32.0 29.0 26.6 24.6 22.8 21.3 20.0 18.8
5/8 3/4 89.9 59.9 44.9 35.9 30.0 25.7 22.5 20.0 18.0 16.3 15.0 13.8 12.8 12.0 11.2 10.6
3/4 7/8 66.0 44.0 33.0 26.4 22.0 18.9 16.5 14.7 13.2 12.0 11.0 10.2 9.4 8.8 8.3 7.8
7/8 1 56.2 37.4 28.1 22.5 18.7 16.0 14.0 12.5 11.2 10.2 8.6 8.3 8.0 7.5 7.0 6.6
1 1-1/8 53.3 35.5 26.6 21.3 17.8 15.2 13.3 11.8 10.7 9.7 8.2 7.9 7.6 7.1 7.0 6.3
1-1/8 1-1/4 43.1 28.8 21.6 17.3 14.4 12.3 10.8 9.6 8.6 7.8 6.6 6.4 6.2 5.8 5.4 5.1
1-1/4 1-3/8 35.7 23.8 17.8 14.3 11.9 10.2 8.9 7.9 7.1 6.5 5.5 5.3 5.1 4.8 4.5 4.2 RRoodd
DDiiaa
HHoollee
DDiiaa
UULLTTRRAABBOONNDD 11330000 UUssaaggee EEssttiimmaattee GGuuiiddee –– 2222 oozz.. CCaarrttrriiddggee SSyysstteemm –– DDeeffoorrmmeedd BBaarr
EEmmbbeeddmmeenntt DDeepptthh ((iinn..))
((iinn..)) ((iinn..)) 22 33 44 55 66 77 88 99 1100 1111 1122 1133 1144 1155 1166 1177
#3 7/16 264.1 176.1 132.1 105.6 88.0 75.5 66.0 58.7 52.8 48.0 44.0 40.6 37.7 35.2 33.0 31.1
#4 5/8 172.5 115.0 86.3 69.0 57.5 49.3 43.1 38.3 34.5 31.4 28.8 26.5 24.6 23.0 21.6 20.3
#5 3/4 119.8 79.9 59.9 47.9 39.9 34.2 30.0 26.6 24.0 21.8 20.0 18.4 17.1 16.0 15.0 14.1
#6 7/8 94.3 62.9 47.2 37.7 31.4 26.9 23.6 21.0 18.9 17.1 15.7 14.5 13.5 12.6 11.8 11.1
#7 1 84.3 56.2 42.1 33.7 28.1 24.1 21.1 18.7 16.9 15.3 14.0 13.0 12.0 11.2 10.5 9.9
#8 1-1/8 66.6 44.4 33.3 26.6 22.2 19.0 16.6 14.8 13.3 12.1 11.1 10.2 9.5 8.9 8.3 7.8
#9 1-1/4 53.9 35.9 27.0 21.6 18.0 15.4 13.5 12.0 10.8 9.8 9.0 8.3 7.7 7.2 6.7 6.3
#10 1-1/2 37.4 25.0 18.7 15.0 12.5 10.7 9.4 8.3 7.5 6.8 6.2 5.8 5.3 5.0 4.7 4.4
#11 1-5/8 31.9 21.3 16.0 12.8 10.6 9.1 8.0 7.1 6.4 5.8 5.3 4.9 4.6 4.3 4.0 3.8 RRoodd
DDiiaa
HHoollee
DDiiaa
UULLTTRRAABBOONNDD 11330000 UUssaaggee EEssttiimmaattee GGuuiiddee –– 5533 oozz.. CCaarrttrriiddggee SSyysstteemm –– TThhrreeaaddeedd RRoodd
EEmmbbeeddmmeenntt DDeepptthh ((iinn..))
((iinn..)) ((iinn..)) 22 33 44 55 66 77 88 99 1100 1111 1122 1133 1144 1155 1166 1177
3/8 7/16 509 339.3 254.5 203.6 170 145 127 113 102 92.5 84.8 78.3 72.7 67.9 63.6 59.9
1/2 9/16 384.9 256.6 192.4 154 128 110 96.2 85.5 77.0 70.0 64.1 59.2 55.0 51.3 48.1 45.3
5/8 3/4 216.5 144.3 108.3 86.6 72.2 63.2 54.1 48.1 43.3 39.4 36.1 33.3 30.9 28.9 27.1 25.5
3/4 7/8 159.1 106.0 79.5 63.6 53.0 46.4 39.8 35.3 31.8 28.9 26.5 24.5 22.7 21.2 19.9 18.7
7/8 1 135.3 90.2 67.7 54.1 45.1 39.0 33.8 30.1 27.1 24.6 22.6 20.8 19.3 18.0 16.9 15.9
1 1-1/8 128.3 85.5 64.1 51.3 42.8 37.5 32.1 28.5 25.7 23.3 21.4 19.7 18.3 17.1 16.0 15.1
1-1/8 1-1/4 103.9 69.3 52.0 41.6 34.6 30.0 26.0 23.1 20.8 18.9 17.3 16.0 14.8 13.9 13.0 12.2
1-1/4 1-3/8 85.9 57.3 42.9 34.4 28.6 25.0 21.5 19.1 17.2 15.6 14.3 13.2 12.3 11.5 10.7 10.1 RRoodd
DDiiaa
HHoollee
DDiiaa
UULLTTRRAABBOONNDD 11330000 UUssaaggee EEssttiimmaattiinngg GGuuiiddee –– 5533 oozz.. CCaarrttrriiddggee SSyysstteemm –– DDeeffoorrmmeedd BBaarr
EEmmbbeeddmmeenntt DDeepptthh ((iinn..))
((iinn..)) ((iinn..)) 22 33 44 55 66 77 88 99 1100 1111 1122 1133 1144 1155 1166 1177
#3 7/16 636.3 424.2 318.1 254.5 212 181 159 141 127 116 106 97.9 90.9 84.8 79.5 74.9
#4 5/8 415.7 277.1 207.8 116.3 139 119 104 92.4 83.1 75.6 69.3 64.0 59.4 55.4 52.0 48.9
#5 3/4 288.7 192.4 144.3 115.5 96.2 82.5 72.2 64.1 57.7 53.5 48.1 44.4 41.2 38.5 36.1 34.0
#6 7/8 227.2 151.5 113.6 90.9 75.7 64.9 56.8 50.5 45.4 41.3 37.9 35.0 32.5 30.3 28.4 26.7
#7 1 203.0 135.3 101.5 81.2 67.7 58.0 50.7 45.1 40.6 36.9 33.8 31.2 29.0 27.1 25.4 23.9
#8 1-1/8 160.4 106.9 80.2 64.1 53.5 45.8 40.1 35.6 32.1 29.2 26.7 24.7 22.9 21.4 20.0 18.9
#9 1-1/4 129.9 86.6 65.0 52.0 43.3 37.1 32.5 28.9 26.0 23.6 21.7 20.0 18.6 17.3 16.2 15.3
#10 1-1/2 90.2 60.1 45.1 36.1 30.1 25.8 22.6 20.0 18.0 16.4 15.0 13.9 12.9 12.0 11.3 10.6
#11 1 5/8 76.9 51.2 38.4 30.7 25.6 22.0 19.2 17.1 15.4 14.0 12.8 11.8 11.0 10.2 9.6 9.0
Note: the above usage charts include a 15% waste factor.
22 & 53 oz
Cartridge
Systems
1:1 Ratio
Manufactured In The U.S.A. by Adhesives Technology Corp.
450 East Copans Road ■ Pompano Beach, FL 33064 ■ (800) 892-1880 ■ Fax (800) 362-3320 ■ www.atc.ws
Page 4 of 5
Ultrabond 1300
Sample Specification – Anchoring adhesive shall be a two component, 1:1 ratio, 100% solids epoxy system
supplied in a two component side by side cartridge and dispensed through a static mixing nozzle supplied by the
manufacturer. Epoxy must meet the requirements of ASTM C881 specification for Type I, II, IV, and V, Grade 3,
Class B, & C. Epoxy must have a minimum heat deflection temperature of 131°F (57°C), per ASTM D648. Adhesive
shall have a working time of 20 minutes (75° F) and a bolt up time of 2 hours (75° F). Shelf life must be a minimum
of two years. Adhesive shall be Ultrabond 1300 manufactured by Adhesives Technology Corp., Pompano Beach, FL.
5. Installation
Job site preparation and work flow – to achieve the desired results, carefully follow these procedures!
• Always be sure the holes are prepared in advance before starting a new cartridge. If at all possible, schedule dispensing to
consume an entire cartridge at one time with no interruption of epoxy flow.
To achieve maximum flow and reduce fatigue, break off
the nozzle to the largest diameter that will fit into the
hole or screen. If the hole is 5/8” diameter or larger, snap
off the smaller diameter section before using.
Most nozzles snap off
to accommodate
varying hole diameters
and depths.
Dual Cartridge Anchoring & Doweling – Hole Preparation and Cartridge Set up
I. Drill
hole to
proper
diameter
and
depth.
Blow out
dust
from the bottom of the
hole. Brush the hole with
a nylon brush. Blow out
dust again. The hole
should be clean of dust
and debris.
II. Insert cartridge
into dispenser making
sure it is properly
positioned with
shoulder of cartridge
flush with top bracket
of the dispenser.
III.
Remove
plastic
cap from
the tip of
the
cartridge.
Dispense a small amount
of epoxy into a disposable
container until you get an
even flow of black and
white material.
IV. Place
nozzle
onto
cartridge
and slide
nut over
nozzle and
thread nut onto cartridge. No nut is
necessary on mixers with built in nut.
Make sure that the nozzle, nut and
cartridge assembly is secure.
Dispense enough epoxy into a
disposable container until the color
becomes a consistent gray with no
streaks.
Anchoring Into Concrete
V. Dispense the material from the bottom of the
hole. Fill approximately 1/2 – 5/8 of the hole depth
while slowly withdrawing the nozzle. Fill completely
full for holes totally submerged in water.
VI. Insert the threaded rod or rebar to the
bottom of the hole while turning clockwise. The
threaded rod or rebar should be free of dirt,
grease, oil, or other foreign materials. Do not
disturb or bolt-up until minimum bolt-up time
has passed.
Anchoring Into Hollow Block or Unreinforced Masonry (Repeat steps I through IV as shown above).
V. Insert the mixing nozzle into the
bottom of the screen and
completely fill while withdrawing
the nozzle. Fill the screen
completely all the way to the end
to insure that the epoxy completely
fills the screen from top to bottom
when threaded rod is inserted.
VI.
Insert
the
epoxy-
filled
screen
into the
hole.
VII. Insert the threaded rod or
dowel to the bottom of the screen
while turning clockwise. The
threaded rod or rebar should be
free of dirt, grease, oil or other
foreign material. Do not disturb or
bolt-up until minimum bolt-up
time has passed.
Manufactured In The U.S.A. by Adhesives Technology Corp.
450 East Copans Road ■ Pompano Beach, FL 33064 ■ (800) 892-1880 ■ Fax (800) 362-3320 ■ www.atc.ws
Page 5 of 5
Ultrabond 1300
BUILDING CODES
Installation of Ultrabond 1300 must comply with
applicable local, state and national code
requirements.
SITE CONDITIONS
Material shall be delivered in original unopened
containers and stored in a dry environment at a
temperature between 40° and 95°F.
PRECAUTIONS
• Wear safety glasses
• Avoid prolonged contact with skin.
• Keep out of reach of children
• Do not take internally
• If Ingested and conscious, give large
quantities of water or milk. Do not induce
vomiting. Call a physician
• Eye contact. Flush with water for at least 15
minutes. Call a physician
6. Availability and Cost
AVAILABILITY
Ultrabond 1300 is available through select
distributors who can provide you with all of your
construction needs. Please contact Adhesives
Technology Corp. at (800) 892-1880 for a
distributor near you.
COST
Cost information is available from your local
distributor.
7. Warranty
All warranties of the product listed herein, in the
corresponding ATC catalog, and in any other
current literature, expressed or implied, including
warranties of merchantability and fitness for a particular
purpose are specifically and expressly excluded, with
the following exception: At its sole discretion, ATC will
repair or replace any product which it considers to be
defective in material or workmanship, excepting normal
wear and tear within sixty (60) days from the date of
purchase from ATC. ATC shall not be liable for any
injury, loss or damage, direct, indirect, incidental or
consequential or arising out of use of, misuse of,
negligence, accident or inability to use any ATC product.
8. Technical Services
For technical support contact Adhesives Technology
Corp. at (800) 892-1880.
9. Maintenance
None required.
10. Filing System
Additional product information and specifications are
available either on line at www.atc.ws or contact
Adhesives Technology at (800) 892-1880 to get copies
mailed to you.
PARTIAL LIST OF PROJECTS USING Ultrabond 1300
Ultrabond 1300 has been used on many high profile
projects including:
Cleveland Hopkins International Airport – Cleveland,
Ohio.
Tampa International Airport – Tampa, Florida.
MARTA Light rail project in Atlanta.
Miami International Airport – Miami, Florida.
Orlando International Airport – Orlando, Florida
Actual user performance and data may differ due to variations of base material, installation procedures and
personnel, weather conditions and other factors. Adhesives Technology Corp. reserves the right to change
specifications or information printed in this Tech Data Sheet without notice or liability for these changes.
Adhesives Technology Corp. will not be liable for any claim based on the use of data or other information printed
in this Tech Data Sheet.