Gulf Bearing-SP 950426 (5)Ring'Tite® P~
'water p!pe *
200
Meets
A.WWA
For use in
municipal water systems,
firelines and other
critical services.
Strength
Class 100, 150 and 200 Blue Brute water
pipes have long-term hydrostatic
strength that meet the commonly
accepted high safety requirements of
municipal water systems. Blue Brute
conforms to cast iron O.D.'s and is
available in 4", 6", 8", 10" and 12" sizes
in Class 100, 150, and 200.
Meets AWWA C900
Underwriters Laboratories and NSF
Listed, Factory Mutual Approved.
J-M Manufacturing's Blue Brute
Class 150 and 200 PVC water pipes
are listed for critical use in firelines
and water mains and are F/M approved.
Blue Brute Class 100 is intended for
water mains.
Light weight
A 20 foot length of Class 150, 8" Blue
Brute water pipe weighs approximately
181 pounds. That makes it easy to load,
easy to transport and easy to handle.
Installers prefer it because it goes into the
ground quickly -- thus saving on
installation costs.
Corrosion resistance
Blue Brute is unaffected by electrolytic or
galvanic corrosion, or any known soil or
water condition. You don't have to worry
about tuberculation, or the need for costly
lining, wrapping, coating or cathodic
protection.
Quality control
Without exception, each length of pipe is
hydrostatically tested and subject to
inspection by our quality control
inspectors throughout every step of the
manufacturing process.
Long laying lengths
A standard laying length of Blue Brute
PVC water pipe is 20 feet. That means
you can cover a lot of ground during
installation. At the same time, you
eliminate the cost of unnecessary joints.
Flow capacity
This PVC water pipe has a smooth
interior that stays smooth over long years
of service with no loss in carrying
capacity. Its coefficient of flow is C = 150
(H&W) -- the best available in common
use in water systems. This capacity often
allows savings in pumping costs as well
as savings on the size of pipe required.
Field cutting
You can cut Blue Brute with a powersaw
or an ordinary handsaw. It eliminates the
;need to invest in costly cutting equipment.
Service life
Because it is nonmetallic, the pipe does
not lose strength due to either potable
water corrosion or external galvanic or
soil corrosion. And its design includes a
surge allowance for a 2 ff./sec, stoppage
of f{ow.
Ring-Tite joints with
factory installed rings
Blue Brute's Ring-Tite joint can be
assembled quickly. Seated in a deep
groove, the flexible elastomeric ring
provides a tight seal that protects the
line from shock, vibration, earth move-
ment and compensates for expansion
and contraction of pipe lengths. And
there's no field mixing or application
of cement. It's a simple push-together
joint that remains tight under normal
operating conditions.
Ring-Tite joint with
factory installed rincj
factory installed Spigot pipe
rubber sealing ends are
ring provides supplied
tight, flexible from factory
seal with bevels.
The bell is an integral
part of the pipe length
with the same strength.
Installation
Product should be
installed in accordance
with J-M Publication
TR-704B, "Blue
Brute® PVC Class
Water Pipe, Installation
Guide."
Short form
specification
le
Accessories
Blue Brute is backed up by all the items it
takes for smooth installation of water
pipe. Direct taps can be made with proper
tapping tools. (See detailed instructions
on tapping in the "Blue Brute Installation
Guide", TR-704B.)
Cast iron O.D.
Available in 4", 6", 8", 10" and 12" sizes,
this pipe can be connected directly into
cast and ductile iron fittings without
adaptors or complicated procedures.
Scope
This specification designates general
requirements for unplasticized po!yvinyl
chloride (PVC) plastic class water pipe
with integral bell and spigot joints for
the conveyance of water and other fluids.
Materials
Pipe shall meet the requirements of
AWWA C900, "Polyvinyl Chloride (PVC)
Pressure Pipe". All Class 100 pipe shall
meet the requirements of DR 25, Class
150 pipe shall meet the requirements of
DR 18 and Class 200 the requirements
of DR 14.
Pipe
All pipe shall be suitable for use as
pressure conduit. Provisions must be
made for expansion and contraction at
each joint with an elastomeric ring.
The bell shall consist of an integral wall
section with a factory installed, solid
cross section elastomeric ring which
meets the requirements of ASTM F-477.
The bell section shall be designed to
be at least as hydrostatically strong as
the pipe wall and meet the requirements
of AWWA C900. Sizes and dimensions
shall be as shown in this specification.
Hydro Testing
Each pipe shall be tested to four times
the pressure class of the pipe for a
minimum of 5 seconds. The integral
bell shall be tested with the pipe.
Standard Laying Lengths
Standard laying lengths shall be
20 feet (4- 1 ") for all sizes.
Pipe stiffness
The pipe stiffness using F/fy for PVC
class water pipe is contained in the table
below:
Class DR F/Ay(psi)
100 25 129
150 18 364
200 14 815
Quick burst test
Randomly selected samples tested in
accordance with ASTM D 1599 shall
withstand, without failure, pressures
listed below when applied in 60-70
seconds.
Minimum burst
Class pressure at73°F(psi)
100 535
150 755
200 985
Drop impact test
Pipe shall withstand, without failure at
73°F, an impact of a falling missile, Tup
C, at the follow:,ng levels. (Per ASTM D
2444).
Pipe Impact
size (in.) (ft./lbs.)
4 100
6 100
8 100
10 120
12 120
There shall be no visible evidence of
shattering or splitting when the energy is
imposed.
Flow characteristics
and dimensions
Flow chart
Class 100 (DR 25)
Velocity Head loss Velocity Head loss Velocity Head loss Velocity Head loss Velocity Head loss
ft./sec, psi/100' ff./sec, psi/100' ft./sec, psi/100' ft./sec, psi/100' ft./sec, psi/100'
Gals./ Pipe size (in.)
min. 4 4.39 I.D. 6 6.30 I.D. 8 8.28 I.D. 10 10.16 I.D. 12 12.08 I.D.
100
2OO
3OO
4O0
50O
6OO
7OO
8OO
9OO
1,000
1,500
2,000
2,500
3,000
3,500
2.12 0.16
4.24 0.57
6.35 1.21
8.47 2.07
2.05 0.10
3.07 0.21
4.10 0.35 2.38 0.09
5.12 0.53 2.98 0.14
6.15 0.75 3.57 0.20 2.38 0.07
7.17 0.99 4.17 0.27 2.77 0.10
8.20 1.27 4.76 0.34 3.17 0.13 2.24
9.22 1.58 5.36 0.42 3.56 0.16 2.52
5.96 0.51 3.96 0.19 2.80
8.93 1.09 5.94 0.40 4.20
7.92 0.69 5.60
9.90 1.04 7.00
8.40
9.80
0.05
0.07
0.08
0.17
0.29
0.45
0.62
0.83
Class 1 50 (DR 18)
Gals./ Pipe size (in.)
min. 4 4.23 I.D.
6 6.091.D. 8 7.981.D.
10
9.79 I.D.
12
11.65 I.D.
100
2OO
3OO
4OO
5OO
6OO
7OO
8OO
9OO
1,000
1,500
2,000
2,500
3.000
2.28 0.19
4.57 0.69
6.85 1.46
9.13 2.48
2.20 0.12
3.30 0.25
4.41 0.42 2.57 0.11
5.51 0.64 3.21 0.17 2.13 0.06
6.61 0.89 3.85 0.24 2.56 0.09
7.71 1.18 4.49 0.32 2.98 0.12 2.11
8.81 1.52 5.13 0.41 3.41 0.15 2.41
9.91 1.89 5.77 0.51 3.84 0.19 2.71
6.41 0.61 4.26 0.23 3.01
9.62 1.30 6.39 0.48 4.51
8.52 0.82 6.02
7.52
9.03
0.05
0.06
0.08
0.10
0.21
0.35
0.53
0.74
Class 200 (DR 14)
Gals./ Pipe Size (in.)
Min. 4
4.07 i.D.
6 5,86 I.D. 8 7.68
I.D. 10
9.421.D.
12.
11.20 I.D.
100
20O
3OO
4O0
5OO
6OO
7OO
8OO
1,000
1,200
1,400
1,600
2,000
2,500
3,000
2.47 0.23
4.93 0.83
7.40 1.76
9.86 2.99
2.38 0.14
3.57 0.30 2.08 0.08
4.76 0.51 2.77 0.14
5.95 0.77 3.46 0.21
7.14 1.07 4.16 0.29
8.33 1.43 4.85 0.38
9.52 1.83 5.54 0.49
6.93 0.74
2.30
2.76
3.22
3.68
4.60
5.53
6.45
7.37
9.21
0.08
0.11
0.14
0.18
0.28
0.39
0.52
0.67
1.01
2.28
2.60
3.26
3.91
4.56
5.21
6.51
8.14
9.77
0.06
0.08
0.12
0.17
0.22
0.29
0.43
0.66
0.92
Coefficient of flow is C = 150 {Hazen and Williams).
Velocity and head ioss data are based on nominal inside diameter, which is outside diameter minus twice thickness T (nom.).
Dimensions (average)
Class 100 (DR 25)*
Pipe Outside Nom. inside T (min.) E Approx. Wt.
size (in.) dia. (in.) dia. (in.)** thick. (in.) dim. (in.) Ds lbs./ft.
4 4.80 4.39 .192 4.75 6.4 1.9
6 6.90 6.30 .276 5.50 8.8 3.9
8 9.05 8.28 .362 6.25 11.4 6.7
10 11.10 10.16 .444 7.00 13.8 10.1
12 13.20 12.08 .528 7.80 15.9 14.4
Class 150 (DR 18)*
4 4.80 4.23 .267 4.75 6.5 2.6
6 6.90 6.09 .383 5.50 9.0 5.3
8 9.05 7.98 .503 6.25 11.6 9.2
10 11.10 9.79 .617 7.00 14.1 13.9
12 13.20 11.65 .733 7.80 16.7 19.7
Class 200 (DR 14)*
4 4.80 4.07 .343 4.75 6.8 3.2
6 6.90 5.86 .493 5.50 9.4 6.7
8 9.05 7.68 .646 6.25 12.1 11.6
10 11.10 9.42 .793 7.00 14.3 17.6
12 13.20 11.20 .943 7.80 16.9 25.1
*DR (Dimension Ratio} is the outside diameter divided by the minimum wall thickness T (min.),
**Nominal inside diameter equals the outside diameter minus twice thickness T (nom.).
;S
,le
or
n
,r
2
The physical (or chemical)
properties of J-M products
described herein represent
typical average values ob-
tained in accordance with
accepted test methods and
are subject to normal manu-
facturing variations. They
are supplied as a technical
service and are subject
to change without notice.
WARRANTY
J-M warrants that its standard products are manufactured
in accordance with its applicable material specifications
and are free from defects in workmanship and materials,
using J-M's specifications as a standard. Every claim under
this warranty shall be deemed waived unless in writing and
received by J-M within thirty (30) days of the date the
defect was discovered, and within one (1) year of the date
of the shipment. Claims for product appearance defects,
such as sunbleached pipe etc., however, must be made
within thirty (30) days of the date of the shipment. J-M
must first be given an opportunity to inspect the product
alleged to be defective in order to determine if it meets
J-M specifications and if the handling, installation, and
operating conditions have been satisfactory and in accor-
dance with J-M recommended practices. Products sold by
J-M which are manufactured by others are warranted only
to the extent and limits of the warranty of the manufac-
turer. The limited and exclusive remedy for breach of the
above warranty by J-M shall be the resupply of a like quan-
tity of non-defective product. J-M shall not be liable for any
INCIDENTAL, CONSEQUENTIAL, OR OTHER DAMAGES
OF ANY KIND, INCLUDING, WITHOUT LIMITATION, ANY
EXPENSES FOR REMOVAL OR REINSTALLATION
RESULTING FROM ANY DEFECT. J-M MAKES NO OTHER
REPRESENTATION OR WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, IN FACT OR IN LAW, INCLUDING,
WITHOUT LIMITATION, THE WARRANTY OF MERCHAN-
TABILITY AND WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE, OTHER THAN THE LIMITED
WARRANTY SET FORTH HEREIN.
J-M SALES & MARKETING / J-M PIPE CUSTOMER SERVICE CENTER
201/535-1 633 OR 800/621-4404
J-M PI PE
J-M Manufacturing Company, Inc.
9 Peach Tree Hill Road
Livingston, NJ 07039
TRX-27 REV. 9/93
B-Q, Inc.
Madein USA