SS9901-CS040831Greg Wood - Daily Activity Notes / Bore #3
City of Coppell - 30' Force Main Line D
Day
Mort
Tue
Wed
Thurs
Fri
Sat
Mon
Tue
Wed
Thurs
Fri
Sat
Mon
Tue
Date Description of Activities
2-Aug Moved equipment / Set wire line
3-Aug Started pilot #1 390' in, dropped 5 degrees in 30' due to soil conditions.
4-Aug Tripped out and try pilot #2. Soil conditions kicked up. Pulled back to pit
S-Aug New pilot #3 (Down Hole Assembly) Recycler down until 12:00, started drilling around 12:00
same results New Pilot 390' in 4th pilot (4th hole) 5:00 pm recycler down - fuel problems
6-Aug Keep drilling in 4th pilot, got 740' total and hit soft material (35 + 91 - 34 + 71), can not steer
w/mud motor too soft. Tripped all 740' out and put jet assembly on and got back 740'
(end of day)
X-Aug 2 bent stems in pit, change stems, started drilling around 11:00. Drilled 45' (785) and hit hard
soil conditions. Shut down around 4:30 pm
9-Aug Drilled 60' (845) w/jet assembly material too hard drill. Tripped back out to pit installed mud
motor and pushed back in to 660'
lO-Aug Continued drilling w/mud motor. At 11:30 fracked out at lake 930' and lost flow, pulled 4
stems to regain flow install poly swale and left to allow poly swale to set up over night
11-Aug Punched pilot out at 4:00PM too high - boring hard. Stop to control frackouts - pulled back-
dropped pit and adjusted bore and bored back on grade. Around 6:30 shakers down 2 hours
12-Aug
Started cutting back w/24" reamer (to save time) at 2:00. 7:00 - 2:00 - recycler down (electrical
problems) Cut 150' back w/24" reamer & had good flow. 3:00 ran out of water- mud suckers
down and at shop. Recycler up and running at 3:30 broke down again at 4:00. McBride came
out and worked on recycler- worked on recycler until 9:30.
1J-Aug Cut w/24" to 330' - lost flow, frackout pushed back to receiving pit to clean hole. Tripped
back in a nd cut 60 more feet to 390', cutting slow too big of cut for soil conditions.
?4-Aug Pushed back out and installed 18" reamer cut back to 780'
16-Aug Started cutting, lost flow - pushed back 300' to regain flow. Completed cutting bore with 18"
reamer at 5:30. Rick called Mike that night about frackout.
IX-Aug
Cleaned frackout on Mariners Ct. from 7:00 until 12:00. Install 24" reamer and started cutting
got back to 390' mark from 1 st try w/24"reamer, cut to 690' and lost flow, pushed back 360' to
regain flow. 3:00 pm lost water and stopped
Wed 18-Aug Bore rig down all day - Cat Track (hoses)
Thurs 19-Aug Rain out
Fri 20-Aug Started and did not have flow- push back another 300' - regained flow and got back to 690'
good flow
Set 21-,4ug Got to 890' lost flow, pushed back go' and regained flow ~ cut out bore with 24"
2S-Aug Put 36" reamer on and started cutting 30', ljoint,4hours. Recyclerdown-pump(IMPELER$)
2:00 changed mixing pumps
Tue 24-A ~g Cut 300' to 330 mark ~ 50 minutes per stem lost flow at 330' push all the way out to regain flow
back into hole to 330' w/good flow. Rig running hot changed water pump after shut down.
Wed 25-,4ug Cutto510". Stemstookfrom 30 minutes to 1 hour. 6stemsin Iostflow. Rig over-heating.
Pushed back all the way to regain flow. Tripped back to 510' - 8:00 pm. Lost motor on recycler
(Shaker Motor ) (Change motor Wednesday night- completed around 10 pm.)
Thurs 26-Aug Lost flow pushed back 90' went back in and rotary pressure maxed out. Push all the way out &
checked - reamer was full of mud. Started modifying reamer around 6:30 pm. Worked until
9:00 PM
Fri 27-Aug Finished modifying reamer - 10:00 am. Started pulling back in. 11:00 rig broke - alternator -
started back at 12:30. 1:00 broke vice jaw - down rest of day
Sat 26-Aug Rain out
Mort SO-Aug Started cutting 4 stems 120' to 630' clean pit and cuttings until 11:30 - 1:30. 1:30 started
drilling. Rig down at 3:30
Tue 31-Aug Rig down - Hydraulic pumps re-installed at 5:00 pm